This unit was removed from a laboratory as surplus to requirements.

The unit had a bulb that broken (see photo of the unit). The lab decided not to invest in a new lamp as the unit wasn't being used anymore.

We have not tested the unit ourselves other than power-on.

This unit was removed from a lab as surplus to requirements.

The lab manager assured us it was in working order prior to removal. At our site we have powered it on but not tested it further.

It does not come with software.

There are 9 small phials, 2 15ml phials and 7 50ml phials attached.

There is also a waste bottle. Also with it are 25 brand new and sealed Amplification Manifolds and 2 sealed Hybridization Manifolds.

Cable and small blue tube holder also included.

This Illumina High-Speed Microplate Shaker was removed from a university lab where it was surplus to requirements.

The unit does not power on. We replaced the blown fused, but it blew the new one immediately. We are unsure of the fault.

It is in otherwise good cosmetic condition with a few light marks from use.

It is sold for spares or repairs.

This Illuminia Highspeed Microplate Shaker was removed from a university lab where it was surplus to requirements.

The unit powers up and runs up to 2300rpm.

It is in reasonably good cosmetic condition but some of the rubber washers have perished and will not hold a tight grip.

It has 3 shelves and 9 adjustable shelf brackets

This Illumina HiSeq 2500 DNA Sequencing System was removed from a laboratory where it was surplus to requirements. The lab purchased a newer model and had held onto this system in the hopes of a future trade in with Illumina but it never happened. So the system just stayed in their lab unused.

The unit powers on but has not been tested any further. Included is a PC with Sequence Analysis View software on it.The system is in good condition but has a few marks from use.

Included as well as the PC are;

2 boxes of Corning tubes.

12 racks.

A used bottle of liquid coolant.

A Book bottle.

The moving/travel brackets for the unit.

Plus various cables etc.

Illumina iScan Array Scanner, Autoloader 2.x and Newport Isolation System

This was removed from a university lab where it was surplus to requirements.

The system consists of;

1 x Illumina Array Scanner SY-101-1001 with a keyboard in the drawer.

1 x Illumina AutoLoader 2.x

1 x Newport BenchTop Vibration Isolation System

6 x Stacker columns

There are other misc cables and parts with this, but please note there is no PC or software included.

Everything is in good cosmetic condition but has light marks from use.

We were able to power on the main SY-101-1001 iScan unit, but we were unable to power up the autoloader. We changed the fuses but it would still not work. We are unsure of the fault.

It was not tested further.

This Illumina iScan SY-101-1001 Array Scanner with Newport Isolation System & UPS was removed from a university lab where it was surplus to requirements.

Included are;

1 x Illumina iScan SY-101-1001 Array Scanner - The unit powers up but was not tested further.

1 x Newport Benchtop Vibration Isolation System

1 x Powervar Uninterruptable Power Supply - Model ABCE800-22B - The unit powers up but was not tested further.

1 x Monitor Arm Stand

There are other misc cables with this, but please note there is no PC or software included.

Everything is in good cosmetic condition with minor marks from use.

This Impac Electronic GmbH Infrared Transmitter IP1 was removed from a university lab where it was surplus to requirements.

The unit has not been tested as we don't have an appropriate power supply. It is in reasonably good cosmetic condition but has some marks from use.

Optik no. 3838190 - 75mm

It is fitted to clamp/stand which can be removed.

This Impact Test Equipment Ltd Test Sieve SIE1056. 200mm Dia x 125um was removed from a university where it was surplus to requirements.

Stainless Steel Frame.

Stainless Steel Mesh.

125 Mic Aperture.

The unit Comes in the original box and appears to be in good, used condition. The box is water damaged.

This Infors AG CH-4103 Bottmingen HT TR-225 AK-82 Magnetic Drive Platform Shaker was removed from a university lab during a clearout.

The unit is in good used cosmetic condition but it does have various marks and signs of use.

The unit powers up fine but will only run at 160rpm. No other functions appear to work on the unit at all. We suspect the control panel is probably faulty.

The on/off button works and you can change modes but the 'set' button and +/- controls do not change the settings at all.

The top plate measures:

80cm L x 42cm W.

Unit sold as spares / repairs due to the 160rpm issue.

This Infors Ag Ht Ak 15/6 Labotron Low Profile Benchtop Orbital Shaker was removed from a university lab where it was surplus to requirements.

The unit powers up and shakes up to 400rpm. It is in reasonably good condition but has marks from use.

This system was removed from a plant room as surplus to requirements during a lab move. The system was in full working order prior to removal, and was professional disconnected by an engineer.

Included in the lot is:

The Ingersoll-Rand SSR Compressor + Tank (we lifts the compressor off the tank, but tank is still included

The Ingersoll-Rand DA-8 Special

The Domnick Hunter Pneudri DME020

Unfortunately, the copper piping and the 3 units shown between the Domnick Hunter and the Ingersoll-Rand DA-8 Special are not included - when we arrived these had been disposed of, but can be replaced.

Due to the nature of the system you will need to get it profesionally installed and checked upon installation.

This unit was part of an Instron 4500 system in a university laboratory.

We did everything we possibly could to get the complete system out of the facility, but we believe it was craned from a car-park into the basement, and its something we were not able to arrange. So we took all the parts we could remove from the system.

This controller was removed from the system.

One of the plastic tabs on the back is broken. Also the adjuster to remove the rear bracket has come off the bolt.

This Instron Ltd Assy no. A1093-10 ISS - K Part/Board for Tensile Tester was removed from a university lab where it was surplus to requirements.

It is in good cosmetic condition and is boxed. We are unsure if it is new or used but it is stored in an unsealed antistatic bag. It has not been tested.

This Intavis Bioanalytical Instruments BioLane HTI 16V In Situ Hybridization System was removed from a university lab where it was surplus to requirements.

The unit powers up and it successfully ran several self-tests. It was not tested further. It seems some features are password locked, and we were unable to bypass them as unfortunately we don't have the passwords.

It is in reasonable cosmetic condition but has some signs of heavy use.

It is. running Software Ver 1.2.0.2

This unit was removed from a lab during a clearout.

The unit powers on and has passed its own self-test but we have not tested it further.

This Integra Assist Plus Pipetting Robot is being sold on behalf of a university client.

The unit was purchased by the university in June 2020 and was used for about 6 months. It is still in excellent cosmetic condition and is fully working. They estimate

There are various pipettes and tips included with it, some of the boxes have been opened but what is still with it is new and unused.

Listed below is what is included/originally purchased along with the original list prices (Minus any disposables and consumables that may have been used)

The total for the below was £21,959+VAT

1 x ASSIST PLUS Base Unit £13,800.00

1 x Charging / Communication Stand £ 299.00

1 x VIAFLO Pipette 8-Channel, 10 - 300 µl £ 875.00

1 x VIAFLO Pipette 8-Channel, 50 - 1250 µl £ 875.00

2 x Pipette Communication Module £ 95.00

1 x Slanted Plate Holder (0°-30°) £ 481.00

1 x PCR 96 Well Cooling Block £ 180.00

1 x VIAFLO Pipette 12-Channel, 10 - 300 µl £ 980.00

1 x Dual Reservoir Adapter For 10, 25 ml and Divided Reagent Reservoirs £ 392.00

1 x VOYAGER Pipette 8-Channel, 0.5 - 12.5 µl £ 1,480.00

1 x VOYAGER Pipette 8-Channel, 10 - 300 µl £ 1,480.00

1 x Rack for 1.5/2 ml Microcentrifuge Tubes £ 642.00

3 x Pipette Communication Module £ 95.00

In addition to this, they estimate around 70% of the consumables originally ordered with the machine are still included.

The consumables listed below are what were originally ordered - we don't have exact details on whats still included, only that around 70% is still included. The original full price of these consumables was £12,692+VAT.

Disposables

6445 1250 µl GRIPTIP, Sterile, Filter 5 Racks of 96 Tips, V96 100 Packs at £52.70+VAT per pack = £ 5,270.00

6435 300 µl GRIPTIP, Sterile, Filter 5 Racks of 96 Tips, V96 100 packs at £ 50.15 +VAT per pack = £ 5,015.00

4371 10 ml SureFlo Disposable Reservoirs, Sterile, 30 Individually Wrapped, Polystyrene 12 packs at £ 45.90+VAT per pack = £ 550.80

4381 25 ml SureFlo Disposable Reservoir, Sterile, 30 Individually Wrapped, Polystyrene 12 packs at £ 49.30+VAT per pack = £ 591.60

4392 100 ml SureFlo Disposable Reservoirs, Sterile, 200 Bulk, Polystyrene 12 packs at £ 105.40+VAT per pack = £ 1,264.80

There was also an Assist+ Platinum Part Maintenance programme ordered for the system at a cost of £2,340+VAT - we don't have details on what maintenance was carried out but presumably some servicing has been performed under this programme.

Please enquire for further details - viewings are welcome. Open to reasonable offers.

This set was removed from a university lab as surplus to requirements.

We have not tested the units.

This cell counter has been powered on and the touch screen is broken, no matter where you press it always thinks you are pressing in the same spot therefore it is being sold as Faulty/ Spares and Repairs. This piece of equipment has come from a UK University. 

This Invitrogen iBlot Gel Transfer Device was removed from a university lab where it was surplus to requirements.

The unit powers up but was not tested further.

It is in reasonably good cosmetic condition but has some marks from use.