METTLER TOLEDO DSC822e Differential Scanning Calorimeter & ThermoHakke EK45/MTMT

This was removed from a university lab where it was surplus to requirements.

Included are;

-Mettler Toledo DSC822e Differential Scanning Calorimeter

-ThermoHaake EK45/MT

-2 x Platon Flowmeter

-1 x Power supply

All units power up but we were unable to test them further at our facility.

They system is in good cosmetic condition with marks from use.

This Perkin Elmer Pyris 1 Differential Scanning Calorimeter System was removed from a university lab where it was surplus to requirements.

The unit has been inspected and fully tested by a qualified engineer. It was confirmed to be in full working order, but the dongle for the software is missing.

Included with it are;

1 x Perkin Elmer Differential Scanning Calorimeter - Pyris 1

Part no. N537-0050

1 x Dell Optiplex PC (SN-MQ4ZP) With PYRIS 1 SOFTWARE

1 x Microsoft Mouse

1 x Dell Keyboard Model - AT102W (SN-M9801-22017)

1 x Norgren Gas Regulator

1 x Perkin Elmer Pyris 1 Spares Kit (Wooden box)

3 x Perkin Elmer cases with small parts

1 x Perkin Elmer Hammer accessory

1 x Thermometer on stand

Everything is in reasonably good cosmetic condition with some marks from age and use.

Perkin Elmer PYRIS Diamond DSC Differential Scanning Calorimeter & Autosampler

This was removed from a university lab where it was surplus to requirements.

The unit runs and communicates with the software but has not been recalibrated. This requires the use of gas, which we are not permitted to do on our site. The unit has been partially serviced. A report is available on request.

The dongle for the software is not included.

The chiller unit has not been serviced.

Included are;

Perkin Elmer PYRIS Diamond DSC Differential Scanning Calorimeter & Autosampler

Part no. N5360025

SN - 536N2011101

Perkin Elmer Intracooler 2P Cooling Accessory

Model no. FC100PED1

SN - 18256

Dell Optiplex 380

This Thermometric 2277 Thermal Activity Monitor (TAM) System was removed from a university lab where it was surplus to requirements.

The unit powers up but it was not tested further. There is a light flashing "pump failure". We are unsure if this is a fault, or if it is due to the parameters in which it was tested.

It is in reasonably good cosmetic condition with some marks from use. It comes with two covers for the control panel.

Parr 6200 Oxygen Bomb Calorimeter Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on without error. We are unable to test it further at our facility.

Also included are the following:

1 x stainless oval sample bucket 17 x 11 x 21cm at widest (l x w x h)

1 x 12 pack of 1/4" ID o-rings

4 x 12 pack of 3/16" o-rings

1 x 12 pack of 5/32" o-rings

1 x 12 pack of 3/8" o-rings

1 x 12 pack of 1.049" o-rings

1 x 12 pack of 7/8" o-rings

1 x bomb dowel kit No. 10MB3

1 x service clamp head No. 475A

1 x service fixture No. 534A

1 x port connector No. 343VB

2 x display protectors No. 1889E

2 x fuel capsules No. 208AC

1 x roll fuse wire for bomb No. 45C10

1 x stainless flange

2 x packing caps No. 378A

1 x Parr 6200 Instruction Manual Item No. 464M

1 x power lead

This Parr Isoperibol Calorimeter 240 was removed from a university lab where it was surplus to requirements.

The item is in reasonable cosmetic condition but has plenty of marks from use and age.

The item powered on fine and we could interact with the control panel without issue. We attempted to run a test print and were met with Error 3800. We are told this is due to the O2 requirement and is not a fault with the system.

The system was serviced in 2020 not long before it came to us.

We were unable to test it further.

Also included are the following:

1x Parr 1755 Printer

1x Parr/Star Power Supply

Model: AD8340