Items 1 to 7 of 7

Image of item

£ 7,390.00 (ex. VAT) 1 in stock

Blueprinter M3 Industrial Selective Laser Sintering (SLS) Low Noise 3D Printer

ITEM-29641

This Blueprinter M3 Industrial Selective Laser Sintering (SLS) Low Noise 3D Printer was removed from a university lab where it was surplus to requirements.


The unit is in excellent cosmetic condition with little to no marks from use.


The lab reported that the unit cost around 60K when new. The item is in working condition. The manufacturer has gone into Administration so unable to offer further support for the printer.


Build Volume: 200mm x 157mm x 150mm.






Image of item

£ 3,185.00 (ex. VAT) 1 in stock

3D Systems Corporation ProJet 3500 - 3510/3500 HD Max 3D Printer

ITEM-31718

This 3D Systems Corporation ProJet 3500 HD Max 3D Printer was removed from a university lab where it was surplus to requirements.


The unit powers up and is in good cosmetic condition with minor marks from use. It was not tested at our facility, but we are told it was working 3 years ago when last used.



Image of item

£ 2,695.00 (ex. VAT) 1 in stock

Projet 460 Plus 3D Advanced Printer

ITEM-35306

This Projet 460 Plus 3D Advanced Printer was removed from a university lab where it was surplus to requirements.


The unit powers up and runs through the boot sequence without fault.


It is in good cosmetic condition with minor marks from use.


Internal dimensions are: L111cm x W45cm x H46cm.

Image of item

£ 2,335.00 (ex. VAT) 1 in stock

Stratasys Dimension Elite 3D Printer PN - 180-00105 & Accessories

ITEM-31388

This Stratasys Dimension Elite 3D Printer was removed from a university lab where it was surplus to requirements.


The item powers on and runs through calibration upon start up. We were unable to test it further at our facility but we contacted the lab and they said the following;


0.1mm tolerance on prints, some post-print cleaning is necessary. It can be a bit temperamental. The heat heads require cleaning each time the printer is used. it could do with a complete service and replacement heads.


The item is in a good, used cosmetic condition aside from a small scratch on the back.


With it are;

Cartridges (all boxes have remaining percentages written on them) :-

1 x ABS-P430 Model (Olive Green) 4%

1 x Nectarine 4%

2 x Nectarine 10%

1 x White 3%

1 x Yellow 12%

1 x Yellow 98%

1 x Blue 3%

1 x Black 14%

1 x Black 6%

1 x Red (unmarked)


Also included:-

2 x Boxes containing 50 Modelling Bases (PN-340-00200)

2 x Dimension System Software Discs

2 x Spare Bulbs

Tool kit

Wire brush

Anti-Sieze Lubricant

2 x Keys

Ethernet Cable

IEC Lead

5 x Spare Fans


Unit dimensions - L92 W69 H172cm

Storage Compartment - L75.5 W65 H45.5cm


Image of item

£ 1,225.00 (ex. VAT) 1 in stock

MakerBot Replicator Z18 Fifth Generation 3D Printer with Cart 3D Printing

ITEM-17209

This MakerBot Replicator Z18 Fifth Generation 3D Printer was removed from a university lab where it was surplus to requirements.


The unit powers up and the bed moves, but the carriage is disconnected and so we did not carry out any further tests at our site.


It is in good cosmetic condition but has some marks from use.



Image of item

£ 740.00 (ex. VAT) 1 in stock

3DTouch 3D Printer with BfB Touch Single Head Smoke Case 3D Printing

ITEM-17208

This 3DTouch 3D Printer with BfB Touch Single Head Smoke Case was removed from a university lab where it was surplus to requirements.


The university assured us it was in good working order. At our side we have tested that the bed moves but we have not tested it any further.


It is in good cosmetic condition with some marks from use.


There is a small amount of filament and some misc parts with it.

Image of item

£ 455.00 (ex. VAT) 1 in stock

MakerBot Replicator 2X Experimental 3D Printer

ITEM-31309

This MakerBot Replicator 2X Experimental 3D Printer was removed from a university lab where it was surplus to requirements.


We were unable to power it up, as it was supplied without the PSU, but we were informed by the lab that it was in working order prior to removal.


Internal dimensions - L49 x W29 x H28cm

Platform - 25 X 16.5cm


It is in reasonably good cosmetic condition with minor marks from use.

Items 1 to 7 of 7

Filters

Price (£)

to

Condition

Brand