This Knapp Open Shuttle OS100B Flexible Autotomous Robotic Warehouse Shuttle is being sold on behalf of a client. It is surplus to requirements.

The unit is in excellent cosmetic condition and has only seen <50h of use.

Technical information about the Knapp Open Shuttle OS100B:

1. Speed: Up to 1.6 m/s (safe)
2. Max. Acceleration: 1,0m/s²
3. Minimum turn radius: 360° turn at standstill
4. Delivery: both front and rear possible
5. Container dimensions: Up to 800 mm x 600 mm
6. Optional integrated lift (550 mm to 1,500 mm)
7. Maximum load: 100 kg
8. Battery life: Over 6 hours, continuous operation
9. Charging time: Approximately 60 minutes (charge ratio > 1:6)
10. Conveyor top edge: 500 mm to 1,000 mm
11. Protection class: IP20
12. Battery: LiFePo4 (lithium iron phosphate)
13. Communication method: WLAN (b/g/n standard) in 5GHz range
14. Dead weight: 130kg

Collection only from Hanau, Germany.

International Metrology Systems MS Impact Coordinate Measuring Machine

This was removed from a university lab where it was surplus to requirements.

We were unable to test it at our facility but the lab confirmed that it was working prior to removal.

It has a Renishaw Probe Head Controller PHC10-2 and Virtual-DMIS Version 3.2 and Version 4.0 software discs which run it.

Battenfield Microsystem 50 Injection Moulding Machine

This was removed from a university workshop where it was surplus to requirements.

The unit was not tested on our site, but the lab confirmed it was in working order prior to removal.

It is in good cosmetic condition with minor marks.

Mackey Bowley Diffusion Bonder, Cheltenham Induction Heating & Edwards E2M80.

The system was removed from a University Lab as surplus to requirements.

This system powers up and is in good cosmetic condition, we are unable to test it further at our facility.

Mackey Bowley Diffusion Bonder.

Serial No. S9638/91

Chamber Dimensions: L 58cm x W 38cm x H 38cm.

Bed Dimensions: L 80cm x W50cm.

Fitted with: Oerlikon Leybold Vacuum Thermvac. Type: TTR91. Serial No. 230035.

Edwards Speedivalve.

Edwards Speedivac Oil Defussion Pump. Model: 403A. Serial No. 1981.

Eurotherm Controller Type 815 & 818 Installation Manual.

Stenhoj Hydraulik 60 Ton.

Type: 500414.

Serial No. 63153.

Model Year: 1991.

Cheltenham Induction Heating Ltd.

Type: TRI 12.

Serial No. TRI2017.

Instron Control Panel.

Model: 1342.

Serial No. H2003.

Fitted with: Edwards Pirani 11 & Display One Single Channel Vacuum Display.

Display One Single Channel Vacuum Display Manual.

Edwards High Vacuum Pump.

Model: E2M 80.

Serial No. 995.

Comes with: Edwards Backing Roughing Valve. Model: BRV25PK. Serial No. 02011 & Instruction Manual.

Gerber DSC 1500 Single Ply Automated Fabric Cutter

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition, the previous client has stated it was in working order when last used. We were unable to test it at our facility as it has been decomissioned.

Features:

1. Table size: 240 x 158 x 85cm ( l x w x h)
2. Cutting area: 183 x 152cm
3. Cutting speed: 1.1 meters per second

Also includes the following:

1. Gerber carriage controller unit

        Serial No. 2187

        Year 2008

1. HP Elitedesk 800 GI TWR PC running Windows 7 installed with Gerber Cutworks 5.1 software

1. HP KB-1156 keyboard

1. Iiyana Prolite Monitor

1. HP mouse part No. 672651-001

1. Kramer data splitter box

1. Instruction Manual

1. Mechanical and Engineering Manual

1. 7 x Data cables

*A compressed air system of 90 - 120psi at 14L/m is required for operation.*

This jet engine is being sold on behalf of a leading UK universities engineering and aerospace department.

The engine which would have originally cost around 1 million USD was owned by MyTravel Aircraft Engineering. It was designed for the DC10 aircraft.

In 2004, the engine type was retired as MyTravel retired the DC10 and moved to the Airbus Aircraft.

Rather than disposing of the engine, it was moved to this universities engineering department as a training resource for students.

This is a genuine full size jet engine.

Its an extremely rare opportunity to acquire a unit like this.

General Electric Model: CF6-6D1A Jet Engine

Removed from retired DC10-10 Aircraft

Has flown about 40 million miles in its 20-year working life.

Please note - whilst the engine was operational prior to going into storage, it is no longer in service and we can offer no warranties to its current performance. It is initially intended for sale for display / museum purposes only, and therefore we would need to discuss any intended flight of the engine or any of its parts.

There is some damage to the nose of the engine which occurred after the item was collected and is not shown in the original photo. We have got images of the damage.

It is a non negotiable of sale that we will need to diligence check the intended use of any prospective buyer. In most cases, a non-flight disclaimer will be required unless you are able to provide appropriate documentation / evidence to demonstrate that any intended use will meet the requirements of the Civil Aviation Authority or other relevant governing bodies. We can discuss this further with you prior to sale and then we would need to approve any proposed flight plans with our university client prior to sale.

Buchiglasuster 80L Mixing Vessel (Non-Jacketed Glass Vessel) 810013201

This was removed from a university lab where it was surplus to requirements.

We are told it was purchased in 2019 and was barely used.

Project#: 810013201

Article#: 99.31532.0000

Total Capacity: 80L

Year: 2019

The item appears to be in good cosmetic condition with no missing elements. The mixer head is included. It powers up and works well.

This Chroma 8 Channel Battery Cell Programmable Charge/Discharge Tester Model 17208M is being sold on behalf of a client. It is surplus to requirements. It is not currently at our site, but viewings can be arranged.

The unit is in good cosmetic condition and has been stored in the original box for the last year. It was working before it was put into storage.

Some info on the unit;

Chroma’s 17208M is a standalone 8 channel version of their 17011 series high precision charge/discharge tester specifically designed for Lithium-ion batteries, electrical double layer capacitors (EDLC), and lithium-ion capacitors (LIC).

The 17208M comes as a fully integrated system which includes allowing full configuration with reporting and statistics capability.

The new Chroma 17208M-6-30 is a high accuracy (±0.02% of F.S.) programmable charge and discharge tester (6V/30A 8 channels) built with 4 current ranges. It is the best test solution for energy storage products such as battery cells, super capacitors, and lithium ion capacitors.

Vixen Aqua Blast 915 With Air Compressor And Salt Trolley Lab

This system was removed from a university lab, where it was surplus to requirements.

The lab confirmed it was in full working order prior to collection. We are set up to test it at our facility.

VW Golf 1.2 TSI Training Model Fully Functioning With Teaching Software from Block Automotive

Product No. SSC SU Nr.4364

VW Golf Mark VII with 1.2 TSI petrol engine with 5-speed gearbox

Engine No. CJZ 023428

This item was removed from a university where it was surplus to requirement.

The vehicle is in excellent condition, with all body panels remaining undamaged.

The previous owner stated that this VW Golf Training Module is in complete working order and includes all software and documentation. It was recently fitted with a new battery, so no further investment is required. It has also been tested at our facility and found no faults or errors.

It was originally purchased for £22,800 in 2016 from Block Automotive Ltd.

Due to the nature of this item, it would require collection from our Scotland branch.

Also Included:

1 x Servicefactory Automotive Funktionsmodell SSC SU 4364 original software DVD

1 x Copy of software DVD

1 x Circuit diagrams with error codes folder for SSC SU Nr. 4364

1 x Circuit diagrams with error codes folder in German Language

1 x Data cable between the diagnostic box and PC

Buehler Abrasimet 2 Abrasive Cutter 95.C/800.400

This was removed from a university lab where it was surplus to requirements.

The unit powers up and has been connected to the pump. It is in good working order.

It is in reasonable cosmetic condition with the expected kinds of marks from use for a piece of equipment like this.

Model Type - 95.C/800.400

SN - 495.MSC.1956

Metaserv Spindle Speed 3600 rpm

Disc size - 250 x 1.5 x 32mm

Disc Size: 250mm 

Arbor Size: 32mm

Wheel RPM: 2830 RPM 

Vice cutting capacity: 80mm - 75mm diameter 

Safety features: Emergency stop, safety switch, electronic break 

Coolant connection size: 12.5mm 

Drain size: 32MM ID 34MM OD 

Coolant tank size: 23 Litre 

Power: 3 PHASE - No neutral 

Dimensions: : 800 x 550 x 450 mm 

Tank Container dimensions - L50 W36 H29cm

The lid with the pump doesn't fit the tank.

Anritsu Pulse Pattern Generator MP1763B & Anritsu Error Detector MP1764A

These units were removed from a university lab where they were surplus to requirements.

Both units power up but the Pattern generator is showing "INTERNAL CLOCK (OPTION.01)". We are told this is just because they are not linked up. We unfortunately do not have the connecting leads.

They are in good cosmetic condition with minor marks from use.

1x Anritsu Error Detector MP1764A

Model. M06340

1x Anritsu Pulse Pattern Generator MP1763B

Model. M06940

1x Dyno Mill Grinder KDL A

1x Tricool chiller MINAC 005LTS

These items were removed from a university lab where they were surplus to requirements.

Both items are in good cosmetic condition and power on, we are unable to test them further at our facility.

Information from the client states both units are in working order.

Wab Agitator Bead Mill Dyno Mill System Lab

This system was removed from a university lab where it was surplus to requirement.

All units are in good cosmetic condition and powered up, this was tested with our testing cable, but we are unable to test it further at our facility.

Power cable not included.

This system comprises the following:

(The Mill) Elektromotorenwerk Brienz AG CH-3855 Brienz Suisse AK71M-2WKF

Model - AK71M-2WKF

S/N - 993060

STAHL-Fribos AG

Cabinet No. - 07-1015

Drawing No. - 232885

WAB B Nr - 604618

Fribos Ref - 1136629

Wab Agitator Bead Mill Dyno Mill System Lab

This system was removed from a university lab where it was surplus to requirement.

All units are in good cosmetic condition and powered up, this was tested with our testing cable, but we are unable to test it further at our facility.

Power cable not included.

This system comprises the following:

(The Mill) Elektromotorenwerk Brienz AG CH-3855 Brienz Suisse AK71M-2WKF

Model - AK71M-2WKF

S/N - 1015500

STAHL-Fribos AG

Cabinet No. - 6007-9610

Drawing No. - 232885

WAB B Nr - 609042

Schaltag - Ref - 1137726

INDENTEC Hardness Testing Machine Model- 5030SKV Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, we are unable to test it further at our facility.

Durham Magneto Optics Ltd MicroWriter ML Photolithography Controller

This was removed from a university lab where it was surplus to requirements.

Everything powers up but has not been tested further.

The PC contains quite a lot of software.

The programs that are relevant to the system are:

MicroWriter ML Version 2.11.11.0.

Thorlabs apt configuration utility v2.2.5389 14611.

MicroWriter ML will not start up properly as the hardware is not connected. This is not a fault, we just don't have the rest of the system

The Newport Motion Controller/Driver Model XPS control unit is for a table that the microwriter would sit on.

TWI Large Electric Control Panel with 5 x A3200 Aerotech Servo Drivers Lab

This was removed from a university lab where it was surplus to requirements.

The cabinet contains the following items.

Aerotech A3200 Ndrive CP x 5

Serial#1:577057/7

Serial#2:577057/6

Serial#3:681834/7

Serial#4:681834/8

Serial#5:681834/2

All appear to be in really good cosmetic condition with no damage. Two of the units are not inside the cabinet.

National Instruments Signal Conditioning Connector Block x 2

Model: SC-2345

Both have stickers on the front of the items

Sicker on item 1: pH Sensor

Sticker on item 2: Thermocouples Inlet/Outlet Drive Relays

There are other small electrical switches and controllers inside.