Shaking Incubators
Items 1 to 20 of 27

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 9,010.00 (ex. VAT) 1 in stock
New Brunswick Innova 4430 Refrigerated Incubator Double Stack Lab
ITEM-25989
This New Brunswick Innova 4430 Refrigerated Incubator Double Stack was removed from a university lab where it was surplus to requirements.
Both units have been recertified and fully tested by a service engineer. It has had band new bearings and drive belts fitted. They have both been deep cleaned, inside and out.
They have both been tested up to 400rpm and run smoothly.
They are both in reasonably good cosmetic condition but have marks from age and usage.

£ 7,650.00 (ex. VAT) 1 in stock
New Brunswick Innova 4400 Floor Standing Shaking Incubator Double Stack Lab
ITEM-25341
New Brunswick Innova 4400 Floor Standing Shaking Incubator Double Stack
These were removed from a university lab where they were surplus to requirements.
They have been fully tested to incubate and shake by a service engineer. They are in full working order.
Inside dimensions - D57 W93 H44cm
Platform - 46 x 77cm
They come with brackets for stacking, but there are only 3 feet and one of them is broken.

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 6,815.00 (ex. VAT) 1 in stock
New Brunswick Innova 44 Incubator/Environmental Shaker M1282-0002 Lab
ITEM-16782
This New Brunswick Innova 44 Incubator/Environmental Shaker was removed from a university lab where it was surplus to requirements.
The unit has been tested and rebuilt by and service engineer.
It has had the following replacement parts;
Screen.
Control knob.
New mount bolt kit.
The Shaker plate assembly was stripped and rebuilt.
2 x Shaker plate pivot pins.
1 x Shaker plate top bearing.
3 x Shaker bearing.
All brand new rubber isolation washers.
All wires in the motor were cut, re-soldered & heatshrunk etc.
The unit has been tested at 400rpm (max) and the incubator is in full working order.
Included with it are;
Multiple Sized Shaker Flask Clip Kits.
Multiple Sized Screws and Washers - One bottle labelled "Green Shakers", Another labelled " Screws for flask holder".
8 x 25ml Flask Clips.
3 x Plastic bases - 1 x 10cm in diameter, 2 x 7.4cm in diameter.
3 x Alan Keys - all different sizes.
3 x Xcelite P10 5/16 Alan key drivers.
A box of Springs.
A box of small (Same size of 25ml) flask clips.

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 6,340.00 (ex. VAT) 1 in stock
New Brunswick Scientific Innova 44 Incubator/Shaker w/ Accessories
ITEM-24742
This New Brunswick Scientific Innova 44 was removed from a university lab where it was surplus to requirements.
The unit has been seen by a service engineer who has replaced the control pot, bearings, bearing post and shaker plate. It is in full working order.
It is in very good cosmetic condition with only minor marks from use.
M1282-0002

£ 6,000.00 (ex. VAT) 1 in stock
Kuhner Floor Standing Laboratory Incubator Shaker Model - ISF-1-W Lab
ITEM-24435
This Kuhner Floor Standing Laboratory Incubator Shaker Model - ISF-1-W was removed from a university lab where it was surplus to requirements.
Internal Dims:
D64cm x W94cm x H50cm
(Height was measured from the shaker mech to the top of the chamber).
The unit powers on with the incubator and shaker appearing to be in working order There are scratch marks on the LHS of the unit and on the bottom shelf from general use. There are surface stains and marks inside the unit and outside of the unit, from general use. There is a large crack in the inspection perspex on top of the unit that travels right across the length of it. The Perspex is double-glazed and has only cracked the outside layer.
Set temp at 37ºC our thermometer read 38.8ºC
Set temp at 40ºC our thermometer read 40.9ºC
Set temp at 80ºC our thermometer read 76.4ºC
The temperature never reached 80ºC, the unit settled on our thermometer's temperature reading, as above.
Shaking test:
• 20 min-1 (the unit ran smoothly)
• 180 min-1 (the unit ran smoothly)
•300 min-1 (the unit ran smoothly)
Included with it are;
30x small clamps with spring retainers.
Dims: L9cm x W9cm x H6cm
9x large clamps with spring retainers.
Dims: L16cm x W16cm x H9cm

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 4,870.00 (ex. VAT) 1 in stock
Thermo Scientific MAXQ 6000 Incubator Shaker Model 4352 Lab
ITEM-30210
This Thermo Scientific MAXQ 6000 Incubator Shaker Model 4352 was removed form a university lab where it was surplus to requirements.
This unit has been recertified by a service engineer. They fitted a brand new drive belt and door catches. It has been tested and is in full working order. The Thermo temp gauge was for testing purposes only and is not included.
It is in excellent cosmetic condition with only minor marks from use.

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 4,315.00 (ex. VAT) 1 in stock
Thermo Scientific MAXQ 4000 Incubator Shaker Lab
ITEM-30192
This Thermo Scientific MAXQ 4000 Incubator Shaker was removed from a university lab where it was surplus to requirements.
The unit powers up and has been inspected and recertified by a service engineer. It has had the following new parts fitted. It is in good working order.
2 x Gas struts.
3 x Shaker plate bearings.
1 x Drive belt.
It has also had a replacement shaker plate drive section fitted.
It is in excellent cosmetic condition with only minor marks from use.

£ 3,560.00 (ex. VAT) 1 in stock
Barnstead Lab-Line MaxQ 4000 Incubator Shaker Model - SHKE4000-1CE
ITEM-28143
This Barnstead Lab-Line MaxQ 4000 Incubator Shaker Model - SHKE4000-1CE was removed from a university lab where it was surplus to requirements.
The unit powers up and is working. It has been assessed by an engineer who replaced the lid struts and fitted a new drive belt.
The only issue is the main power button on the front of the unit doesn't appear to work. This does not affect the operation of the unit at all. It just needs to be switched on and off at the main supply.
The incubator function was tested with a digital thermometer (not included).
The temperature was first set to 37°c. when reached temp the thermometer read 37.6°c.
The temperature was then set to its max temp of 60°c, when it reached temp, the thermometer read 58.8˚c.

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 3,520.00 (ex. VAT) 1 in stock
New Brunswick Innova 4400 Floor Standing Shaking Incubator Lab
ITEM-25606
New Brunswick Innova 4400 & Innova Shaking Incubator.
This was removed from a university lab where it was surplus to requirements.
The unit has been assessed by a service engineer and has had the following replacement parts fitted.
Motor.
Temperature sensor bracket.
Door mechanism.
Gas struts.
Base.
Various panels.
It has been tested at various speeds and is shaking well.
It has been temperature tested at:
37ºC - It reached this temp fine. We calibrated it with our SmartVue Thermometer (not included).
80ºC - It reached 73ºC and it was at this temperature for quite a while.
The unit is in good cosmetic condition but has marks from use.
The manual is supplied.

£ 3,290.00 (ex. VAT) 1 in stock
New Brunswick Scientific Innova 4330 Refrigerated Shaking Incubator
ITEM-29942
This New Brunswick Scientific Innova 4330 Refrigerated Shaking Incubator was removed from a university lab where it was surplus to requirements.
The unit powers up and the incubator and shaker have both been tested (digital thermometer not included). It is in full working order.
The unit is in good cosmetic condition but the lid seal is starting to detach and likely needs replacing.
Internal Dimensions - 87 x 56 x 34 cm (up to the top where the lid would seal)

RECERTIFIED ITEM
RECERTIFIED ITEM
£ 3,155.00 (ex. VAT) 1 in stock
Infors AI 70 Minitron Laboratory Shaking Incubator Lab
ITEM-26007
This was removed from a university lab where it was surplus to requirements.
The unit has been tested by a service engineer, but will still require calibration upon installation.
The unit is in reasonable used cosmetic condition. A brand new OEM gas strut for the door has been fitted. The shaker works as it should and has been tested up the max of 400rpm.
The unit has been temperature tested at:
37ºC our thermometer showed 34.2ºC.
To get it to run at 37ºC the unit needs to be set to 40ºC
65ºC (Max) our thermometer showed 63.2ºC.
The unit requires calibration.
Internal Dimensions:
41cm L x 48cm D x 40cm H.
Length & Depth are the shaker tray dimensions.

£ 3,030.00 (ex. VAT) 1 in stock
New Brunswick Innova 4300 Incubator Shaker Mfg no. M1193-0100 Lab
ITEM-31245
This New Brunswick Innova 4300 Incubator Shaker was removed from a university lab where it was surplus to requirements.
The unit powers up and has been tested with a digital thermometer (not included). The shaking plate has also been tested. The system is in full working order.
It is in reasonable cosmetic condition with marks from use.
Internal dimensions - L88 W56 D34cm

£ 3,000.00 (ex. VAT) 1 in stock
Medline Scientific Jeio Tech Lab Companion Incubator Shaker IST-3075R
ITEM-31890
This Medline Scientific Jeio Tech Lab Companion Incubator Shaker IST-3075R was removed from a university lab where it was surplus to requirements.
The unit powers on and is in good working order. The shaker runs up to 500rpm and the incubation works.
It is in good cosmetic condition with minor marks from use.
Internal dimensions - L41 W40 H32
Shaker Platform - 35 x 35cm
2 x 1000ml Flask Clamps
Tube Stand holds 10 x 50ml Tubes

£ 2,440.00 (ex. VAT) 1 in stock
Barnstead International Max Q 4000 Laboratory Incubator Shaker SHKA4000-8CE Lab
ITEM-25240
This Barnstead International Max Q 4000 Laboratory Incubator Shaker SHKA4000-8CE was removed from a university lab where it was surplus to requirements.
This unit has been recertified and is in full working order. It has had a new drive belt and a pair of new lid struts fitted.
It has been fully temperature tested.
It is in good cosmetic condition with some marks from use.

£ 1,770.00 (ex. VAT) 1 in stock
New Brunswick Scientific Innova 4000 Benchtop Incubator Shaker Lab
ITEM-30218
This New Brunswick Scientific Innova 4000 Benchtop Incubator Shaker was removed from a university lab where it was surplus to requirements.
The unit powers up and runs up to 500rpm. It was tested with a digital thermometer (not included).
The temperature was first set to 37°c, when reached, the thermometer read 42.8˚c
The temperature was then set to 60˚c (max) when reached, the thermometer read 64.4˚c
It is in reasonable cosmetic condition with some marks from use.
Internal Dimensions:
D48.3 W50.2 H33.6cm

SPARES/REPAIR ITEM
SPARES/REPAIR ITEM
£ 1,765.00 (ex. VAT) 1 in stock
Thermo Scientific Max Q 4000 Shaking Incubator Lab Spares/Repairs
ITEM-30287
This Thermo Scientific Max Q 4000 Shaking Incubator was removed from a university lab where it was surplus to requirements.
The unit would not power up in testing. We swapped the boards out but still could get it to power. There were loose parts inside, so we assume it has been stripped. It has a very worn drive section.
It's in reasonable cosmetic condition with some marks from use.
It is sold for spares/repairs.

£ 1,750.00 (ex. VAT) 1 in stock
New Brunswick Scientific Classic C24 Incubator Shaker Lab
ITEM-31977
This New Brunswick Scientific Classic C24 Incubator Shaker was removed from a university lab where it was surplus to requirements.
The unit is in good working order and has been tested with a digital thermometer (not included). It runs well up to 400rpm.
It is in reasonable cosmetic condition but has some fairly heavy usage marks.
Internal dimensions - L54 W52 H36cm
Shaker Platform - 45.5 x 45.5cm
Tube stand inside holds 20 x 50ml tubes

£ 1,385.00 (ex. VAT) 1 in stock
Gallenkamp IOI400.XX2.C Floor Standing Shaking Incubator Lab
ITEM-12238
This Gallenkamp IOI400.XX2.C Refrigerated Shaking Incubator was removed from a university lab where it was surplus to requirements.
The unit powers up and has been tested.
It was tested using a Thermo Smart-Vue gauge (not included).
The gauge showed 37.4ºC when the unit was set to 37ºC.
The gauge showed 59.8ºC when the unit was set to 60ºC (Max).
The max rpm is 400, which the unit runs fine at. The first digit of the rpm screen does have issues, but the rpm can still be set ok.
It is not a refrigerated unit.
Inner dimensions: 85.5cm L x 35cm W.
Shaker plate dimensions: 69cm L x 49cm W.

SPARES/REPAIR ITEM
SPARES/REPAIR ITEM
£ 1,000.00 (ex. VAT) 1 in stock
New Brunswick Scientific Innova 4230 Refrigerated Incubator Shaker Spares/Repair
ITEM-31913
This New Brunswick Scientific Innova 4230 Refrigerated Incubator Shaker was removed from a university lab where it was surplus to requirements.
The unit powers up and the shaker and the incubation functions work, but it has a compressor fault causing the refrigeration to not work.
It is in good cosmetic condition with marks from use.
Internal dimensions - L60 W53 H62cm
1 Shelf - 51 x 51cm

£ 935.00 (ex. VAT) 1 in stock
Gallenkamp Orbital Laboratory Shaking Incubator Cat no. IOX400.XX1.C Lab
ITEM-25297
This Gallenkamp Orbital Laboratory Shaking Incubator Cat no. IOX400.XX1.C was removed from a university lab where it was surplus to requirements.
The item powers on and the shaker runs up to 400rpm. It has been tested with a digital thermometer (not included).
The temperature was first set to 37°c which it reached quickly. The temperature was then set to its maximum of 70°c, after an hour or so the thermometer was reading 65°C.
The item is in a reasonable, used cosmetic condition.
Unit dimensions - L103 x W68 x H74cm
Inside dimensions - L76 x W55 x D43cm
Platform size - 70 x 50cm
Items 1 to 20 of 27