Engineering and Workshop
Items 1 to 20 of 44
£ 7,970.00 (ex. VAT) 1 in stock
Buehler Abrasimet 2 Abrasive Cutter 95.C/800.400
ITEM-37041
Buehler Abrasimet 2 Abrasive Cutter 95.C/800.400
This was removed from a university lab where it was surplus to requirements.
The unit powers up and has been connected to the pump. It is in good working order.
It is in reasonable cosmetic condition with the expected kinds of marks from use for a piece of equipment like this.
Model Type - 95.C/800.400
SN - 495.MSC.1956
Metaserv Spindle Speed 3600 rpm
Disc size - 250 x 1.5 x 32mm
Disc Size: 250mm
Arbor Size: 32mm
Wheel RPM: 2830 RPM
Vice cutting capacity: 80mm - 75mm diameter
Safety features: Emergency stop, safety switch, electronic break
Coolant connection size: 12.5mm
Drain size: 32MM ID 34MM OD
Coolant tank size: 23 Litre
Power: 3 PHASE - No neutral
Dimensions: : 800 x 550 x 450 mm
Tank Container dimensions - L50 W36 H29cm
The lid with the pump doesn't fit the tank.
£ 3,835.00 (ex. VAT) 1 in stock
Woods 63KO Variable Pitch Aeronautical Engineering Wind Testing Tunnel Lab
ITEM-23928
Woods 63KO Variable Pitch Aeronautical Engineering Wind Testing Tunnel
This was removed from a university engineering department where it was surplus to requirements.
The tunnel was dismantled when we collected so no testing was carried out, but we were told that it was still in operational condition prior to dismantling.
It is in five sections:
Section 1- Main Power/ Fan Unit.-405 kg. 120 cm x 120 cm x 150 cm. Outlet flanges 63 cm inside diameter. 3 phase 5 pin 415V motor.
Section 2- Silencer Unit- 160 kg. 127 cm x 91 cm x 131 cm. Flanges are 79 cm and 63 cm inside diameters.
Section 3- Air Intake Funnel- 155 kg. 170 cm x 121 cm x 145 cm .Apertures are 41cm x 41 cm and 80 cm x 80 cm.
Section 4- Large Tunnel Section-155 kg. 118 cm x 73 cm x 120 cm. Apertures are 41 cm x 41 cm and 64 cm diameter internal.
Section 5- Work Access Unit-85 kg. 55 cm x 55 cm x 160 cm. This has 8 openings 30 cm x 60 cm. It comes with a variety of doors, 8 in total.
£ 3,750.00 (ex. VAT) 1 in stock
Terumo Model TSCD-II Terumo Sterile Tubing Welder Lab
ITEM-41787
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: TSCD-II
REF: ME-SC203AH
Total Welds: 00000556
Next Service: 21/02/2024
Soft Version: S00017
£ 3,700.00 (ex. VAT) 1 in stock
Terumo TSCD-II Model Terumo Sterile Tubing Welder Lab
ITEM-41788
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: TSCD-II
S/N: 202004581
Total Welds: 00001203
Soft Version: S00017
£ 3,650.00 (ex. VAT) 1 in stock
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
ITEM-41786
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: TSCD-II
S/N: 202004580
REF: ME-SC203AH
Total Welds: 00001994
£ 3,600.00 (ex. VAT) 1 in stock
Terumo Type TSCD-II Terumo Sterile Tubing Welder Lab
ITEM-41789
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: TSCD-II
S/N: 201808521
Total Welds: 00005367
Soft Version: S00017
£ 3,550.00 (ex. VAT) 1 in stock
Terumo Model TSCD-II Terumo Tubing Welder Sterile Lab
ITEM-41791
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: SC-203AH
S/N: 2006-09032
Total Welds: 00003071
Soft Version: S00015
£ 3,500.00 (ex. VAT) 1 in stock
Terumo TSCD-II Type Terumo Sterile Tubing Welder Lab
ITEM-41790
Terumo TSCD-II Terumo Sterile Tubing Welder Lab
This item was removed from a university where it was surplus to requirement.
It is in good cosmetic condition and powered on, we are unable to test it further at our facility.
Model: SC-203AH
S/N: 2007-04016
Total Welds: 00006003
Soft Version: S00015
NEW ITEM
NEW ITEM
£ 3,500.00 (ex. VAT) 1 in stock
Zeta Programable Guillotine Cutter GCI-800 Lab
ITEM-34773
Zeta Programable Guillotine Cutter GCI-800
This item was removed from a university where it was surplus to requirement.
It is brand new in its original packaging.
The Item powers on and performs as intended.
All items included:
1x Zeta Programable Guillotine Cutter GCI-800
S/N: GC1800-190601
1x Set of Allen keys.
1x Philips screwdriver
1x Lubricating oil.
1x User manual.
£ 2,500.00 (ex. VAT) 1 in stock
9 x MilliporeSigma Compact 4 Drawer Locking Cart Lab
ITEM-39961
9 x MilliporeSigma Compact 4 Drawer Locking Cart Lab
These items was removed from a university lab where it was surplus to requirements.
Condition as follows:
Very Good: 5
Good: 2
Reasonably Good: 2
All keys included.
£ 1,975.00 (ex. VAT) 1 in stock
MC-80 Water Cooling Manual Metallographic Cutting Machine w/ Stand
ITEM-39849
MC-80 Water Cooling Manual Metallographic Cutting Machine w/ Stand
This was removed from a university lab where it was surplus to requirements.
The unit powers up and is in good working order.
It is in reasonable cosmetic condition for this type of equipment, though it has been well used.
It has a 16amp 5 pin 3phase plug fitted.
£ 1,740.00 (ex. VAT) 1 in stock
Large Pace Soldering Iron & Accessory Bundle ST45/ST50/ST55
ITEM-38350
Large Pace Soldering Iron & Accessory Bundle ST45/ST50/ST55
Included are the following;
- 44 X SODRTEK by pace SensaTemp ST45
- 8 X Pace IntelliHeat ST50
- 15 X Pace SensaTemp ST55
- 60 X Pace Inc Tool stands (2 With no bases)
- 9 X Tip & Tool Stand for TD-200 and TD-100A
- 65 X Mixed Unbranded Soldering Irons with lead and extraction tube
- 7 X PS-90 Universal Soldering Iron (Intelliheat)
- 6 X 1/16 in. Chisel High Capacity Pack of 5 (1 packet is opened but has an extra 3 in the pack)
- 1 X 1/8 in. Chisel Tip
- 10 X PACE 05L0 Tips
This job lot of items comes from a university lab, The items were no longer required.
None of these items have been tested at our site - it is likely that some will be spares / repairs, but we anticipate that a reasonable amount should operate well.
None of these items have been PAT or electrical safety tested. For this reason we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks.
They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the unit. It is an excellent opportunity for anyone looking to benefit for individual equipment resale.
The units have not been tested at all.
£ 1,545.00 (ex. VAT) 1 in stock
Sonimat Ultrasons GP20 with Monitor/Terminal Ultrasoic Welding Controller Lab
ITEM-28173
This Sonimat Ultrasons GP20 with Monitor/Terminal was removed from a university lab where it was surplus to requirements.
The units power up and the monitor/PC unit is working but an alarm sounds.
There don't appear to be any programmes/apps loaded onto the system.
£ 1,365.00 (ex. VAT) 1 in stock
CIF Technodrill 2 CNC Drilling & Milling Prototype Machine Lab
ITEM-23982
This CIF Technodrill 2 CNC Drilling & Milling Prototype Machine was removed from a university engineering department where it was surplus to requirements.
The item is in very good cosmetic condition. The lab said the machine is old technology but they believe it has never been used, having been purchased for an abandoned project some time ago.
It powers up and is in working order.
It can be used for small-scale milling work, in particular, milling printed circuit board designs onto copper-clad FR4 board. It comes complete with a wheeled enclosure made from Aluminium T-slot/acrylic.
The item comes with Galaad 3 user manual, and Galaad 3 CAD-CAM-CNC software for windows as well as some unopened accessories.
Item is wired with EU plugs. An adaptor is needed.
£ 1,300.00 (ex. VAT) 1 in stock
Interlas Syncrotig 375 AC/DC Gas Tungsten-Arc/Shielded Metal Arc TIG Welder
ITEM-26280
This Interlas Syncrotig 375 AC/DC Gas Tungsten-Arc/Shielded Metal Arc TIG Welder was removed from a university engineering lab where it was surplus to requirements.
We haven't tested it at our facility further than powering it up but the lab said it was fully working prior to removal. It is a complete system.
Actual unit dimensions - D58 W80 H143.5cm (comes on a trolley for mobility)
27 x 58cm Platform to hold gas bottles.
it is in reasonably good cosmetic condition with marks from use.
£ 1,285.00 (ex. VAT) 1 in stock
Woods Air Movement Series 28 Fan Wind Testing Tunnel 710/289/1/4
ITEM-21203
Woods Air Movement Series 28 Fan Wind Testing Tunnel 710/289/1/4
This unit came from an engineering university. It was used to develop and test for the motor industry. We were assured it was in good working order.
The Flange/Working Section External Dimension 56cm X 56cm
Included is a basic working section with two access panels. Approximate size of working section
56cm x 56cm X 100cm.
The Fan type is a K. Blackman 28 series.
The fan uses 7.5 kw Electric Motor with an inverter control.
It is split into 4 sections;
Unit 1- Main Fan/Control Unit- 130cmx130cmx175cm.-330 kg
Unit 2- Joint Section- 68cmx62cmx86cm.- 24 kg
Unit 3-Large Tunnel Section- 217 cmx77cmx149cm.- 150 kg
Unit 4- Work Access Unit- 57cmx54cmx81cm.- 22 kg.
Please enquire if you would like a delivery quote.
The last time when the nozzle calibration was ran for that tunnel and it went up to a measured airspeed of 26m/s (94km/h).
£ 1,250.00 (ex. VAT) 1 in stock
Jinan King Rabbit CNC Machine System w/ PSU And Chiller
ITEM-36023
Jinan King Rabbit CNC Machine System PSU And Chiller
This was removed from a university lab where it was surplus to requirements.
The system powers up but has not been tested further.
Includes:
-HPC PSU
-Motion controller
S/N- 13920124
-S&A Industrial Chiller (no cap)
Model number-CW3000AG
Max RPM- 24000
Model number- RC 4040
£ 1,235.00 (ex. VAT) 1 in stock
Struers LaboPol-1 Polishing Machine Lab
ITEM-34939
This Struers LaboPol-1 Polishing Machine was removed from a university lab where it was surplus to requirements.
The unit powers up and is in good working order.
It is in reasonable cosmetic condition but is well used.
£ 1,200.00 (ex. VAT) 1 in stock
Instron 5543 Single Column Table Top Tensile Tester System Spares/Repairs
ITEM-25140
Instron 5543 Single Column Table Top Tensile Tester System Spares/Repairs
This was removed from a university lab where it was surplus to requirements.
The unit did not power up in testing. It is sold for spares/repairs.
Included are the following;
Accessories.
1x lockable tool chest with misc bit items inside.
1x user manual
1x Materials testing quick guide (laminated)
1x home made timer box (plug removed)
1x Transducer unit
£ 985.00 (ex. VAT) 1 in stock
Vickers-Armstrong Pedestal Hardness Tester Lab
ITEM-37040
Vickers-Armstrong Pedestal Hardness Tester
This was removed from a university lab where it was surplus to requirements.
The unit is in reasonably good cosmetic condition with marks from use.
The system is mechanically sound, but we were told by the lab that the diamond might be damaged. We have been unable to confirm or deny this.
Items 1 to 20 of 44