Workshop

SPARES/REPAIR ITEM

£ 310.00 (ex. VAT) 1 in stock

Thermo Scientific Benchtop Laboratory Centrifuge Heraeus Megafuge 40R Lab

ITEM-36099

Thermo Scientific Benchtop Laboratory Centrifuge Heraeus Megafuge 40R

This was removed from a university lab where it was surplus to requirements.

The unit has a main board fault, but the following parts have been confirmed as working and useful for spares.

Motor

Display

Compressor

Lid latches

It is in good cosmetic condition with marks from use.

It is sold for spares/repairs.

SPARES/REPAIR ITEM

£ 305.00 (ex. VAT) 1 in stock

Nuaire IR Direct Heat Incubator Model No. NU-5510E Lab

ITEM-37276

Nuaire IR Direct Heat Incubator Model-NU-5510E Lab

This item was removed from a university where it was surplus to requirements.

The unit powers up and has been successfully temperature tested.

However, due to a suspected CO2 Sensor/Air Pump fault, this item is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Thermo Scientific MaxQ 4000 Analog Incubator Shaker SHKA4000-1CE Faulty

ITEM-37029

Thermo Scientific MaxQ 4000 Analog Incubator Shaker

This was removed from a university lab where it was surplus to requirements.

The unit would not power up and tripped the electrics during testing. We believe the motor controller is faulty. The gas struts for the lid have also failed.

It is in otherwise good cosmetic condition with marks from use.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Life Technologies Floid Cell Imaging Station & Recovery Drives Lab Fauty

ITEM-36438

Life Technologies Floid Cell Imaging Station

This was removed from a university lab where it was surplus to requirements.

The unit powers up but is stuck in a boot loop. It is in good cosmetic condition with marks from use.

It is sold for spares/repairs

With it are;

1x Floid Rescue Disk Memory Stick

1x Evo Floid Recovery Memory Stick

1x GlobTek 9 volt Power Supply

M/N: GT-81081-6012-T3

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Syngene Chemi Genius 2 BIO Imaging System with PC & GeneSnap Software

ITEM-35699

This was removed from a university lab where it was surplus to requirements.

The system powers up but we were unable to get it to communicate with the PC.

Everything is in good cosmetic condition but is sold for spares/repairs.

Syngene Chemi Genius 2 BIO Imaging System

Model: ChemiGenius2

Serial#: SYDR2/1569

The unit is in good cosmetic condition both internally and externally with minor surface damage. It powers on with a green light illuminated at the front.

Items internal kettle lead does not connect to the Syngene GV2M30 transilluminated stage, although when powered with an external kettle lead the stage successfully powered on.

Syngene GV2M30 Transilluminated Stage

Model: GV2M30

Serial#: SYGV2/1594

Item powers on with use of external kettle lead.

When powered on all switches and UV light are fully functional.

Unable to test further.

RM Expert 3030 PC

Model: Expert 3030

Serial#: 1053612636

Item powers on.

Unable to connect to Syngene unit.

Item has Gene Snap Software installed Version 6.08.04.

When opening software a message appears: 'NO BYTES READ!' Serial Port Failure.

HP LP2065 Monitor

Model: LP2065

Serial#: CNG709063D

Item powers on and communicates with PC.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Andor Metal Halide Light Source AMH-200-F06S Lab Spares/Repairs

ITEM-35597

This Andor Metal Halide Light Source AMH-200-F0/6S was removed from a university lab where it was surplus to requirements.

The unit powers up but is showing bulb fault 1, which the manual suggests is a data socket issue. The lamp hours are not registering. It is likey the bulb needs replacing.

It is in otherwise good cosmetic condition with minor marks.

Sold for spares/repairs.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Carl Zeiss 47 30 12 - 9901 Stereo Microscope System Lab

ITEM-34815

THis was removed from a university lab where it was surplus to requirements.

The unit powers up but none of the objectives are particularly clear, and two don't show an image at all (detailed below). The unit is quite stiff and awkward to use.

For these reasons it is sold for spares/repairs.

It is in reasonable good cosmetic condition with minor marks.

2x Carl Zeiss Kpl 8x Eyepieces

1x Leitz Wetzlar H 20x/0.40 ∞/1.80 Quarzgl. (no clear image)

1x Carl Zeiss 4494688 Ph2 40x/0.75 160/0.17

1x Carl Zeiss 4459404 Ph2 NEOFLAUR 25x/0.60 160/0.17

1x Carl Zeiss 4836489 Ph2 NEOFLAUR 16x/0.40 160/-

1x Carl Zeiss 4111437 Ph3 NEOFLAUR 100x/1.25 oil 160/- (no clear image).

1x Carl Zeiss Nose Piece III RS 46 62 49-9904

1x Carl Zeiss Stage 47 33 56-9901

1x Carl Zeiss Condenser 4680811

1x Carl Zeiss Microscope power supply 47 20 83 6 volt and 12 volt output.

1x Carl Zeiss Lamp power supply VHW 50f-2b 39 26 41 showing 365 hours and 55 minutes.

1x Carl Zeiss Lamp 12 volt 100 w 46 8019-9901

1x Carl Zeiss Lamp HBO 50 w 46 80 32-9902

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

CTC Analytics Leap Technologies HTCPAL Autosampler Spares/Repair Lab

ITEM-46757

CTC Analytics Leap Technologies HTCPAL Autosampler Lab

This item was removed from a university where it was surplus to requirement.

It is in reasonably good cosmetic condition and powers on, however as displayed the controller screen is damage.

Therefore, it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Coffetek Gourmet Vitro 6 4 Cannister Touch Display Coffee Machine Spares/Repairs

ITEM-44399

Coffetek Gourmet 83545 Touch Display Coffee Machine Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on.

The unit has now powder hoppers or drip trays. It is sold for spares/repairs.

Key not included.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Coffetek Gourmet Vitro 6 4 Cannister Touch Display Coffee Machine Spare/Repair

ITEM-44398

Coffetek Gourmet 83545 Touch Display Coffee Machine Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, but is missing the powder hoppers and drip tray. It is sold for spares/repairs

Key not included.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Julabo SE High Tech Heating Circulator Water Bath Spares/Repair Lab

ITEM-38834

Julabo SE High Tech Heating Circulator Water Bath

This item was removed from a university laboratory where it was surplus to requirements.

It powers on but has an electrical issue with the screen, which keeps powering on and off.

Additionally, it does not include a bung and is therefore listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Coffetek Gourmet Vitro 6 4 Cannister Touch Display Coffee Machine

ITEM-44401

Coffetek Gourmet 83545 Touch Display Coffee Machine Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, however as it has been out of use for 5+ years it would require servicing before use.

There is no drip tray included.

It is sold for spare/repairs

Key not included.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Coffetek Gourmet Vitro 6 4 Cannister Touch Display Coffee Machine

ITEM-37210

Coffetek Gourmet 83545 Touch Display Coffee Machine Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on. The unit has no power hoppers and is missing the drip tray. It is sold for spares/repairs

Key not included.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Fisher Scientific Isotemp 3016S Recirculating Water Chiller / Heating Faulty

ITEM-42266

Fisher Scientific Isotemp 3016S Recirculating Water Chiller / Heater

This item was removed from a university laboratory where it was surplus to requirements.

It is in very good cosmetic condition and powers.

However, two LED bars on the display screen are not illuminating, resulting in inaccurate temperature readings during operation.

Therefore, it is listed as Spares/Repair

Specifications:

Model: Isotemp 3016S
Serial No.: 110179038

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Becker VTC 6/2-09 Motor Pump (Cracked Casing)

ITEM-41338

Becker VTC 6/2-09 Motor Pump

This item was removed from a university lab where it was surplus to requirement.

It is in reasonably good cosmetic condition and powers on, there is a crack in the fan's outer casing and therefore, it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Datarack Floor Standing Server Rack 4 Shelves

ITEM-40048

Datarack Floor Standing Server Rack 4 Shelves

These were removed from a university lab where they were surplus to requirements.

The unit is missing a wheel.

It is sold spares/repairs.

Includes 4 shelves 58x58cm

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Migatronic KDO 400 CO2 MIG Welder Spares/Repairs

ITEM-44958

Migatronic KDO 400 CO2 Welder

This system was removed from a university lab where it was surplus to requirements.

The unit has not been powered on due to damaged cables, making it a visual PAT fail (see photos). Other than that, it is in reasonable cosmetic condition.

Due to the damaged cables, this item is listed as Spares/Repair.

Specifications:

Model: KDO 400
Serial No.: 8909 1293

$Image of Teltron Model 580 Tel-X-Ometer X-Ray Diffraction Unit Lab$

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Teltron Model 580 Tel-X-Ometer X-Ray Diffraction Unit Lab

ITEM-42311

Teltron Ltd Tel-X-Ometer 580 X-Ray Generator Deflection System

This item was removed from a university laboratory where it was surplus to requirements.

It is in very good cosmetic condition, contained in its original packaging.

The lid mechanism operates smoothly, and the deflection holder plate moves without issue around the main dial. It has not been powered on or tested further at our facility.

However, despite the good physical condition, the previous owner reported that although the unit produces x-rays but is not stable enough to be used.

And therefore, is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Teltron Ltd Tel-X-Ometer 580 X-Ray Generator Deflection System Lab

ITEM-42310

Teltron Ltd Tel-X-Ometer 580 X-Ray Generator Deflection System

This item was removed from a university laboratory where it was surplus to requirements.

It is in very good cosmetic condition, contained in its original packaging.

The lid mechanism operates smoothly, and the deflection holder plate moves without issue around the main dial. It has not been powered on or tested further at our facility.

However, despite the good physical condition, the previous owner reported that the unit does not produce x-rays and is therefore listed as Spares/Repair.

Serial No.: FR04-01

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Precision Scientific NAPCO 5430 Dual Chamber Co2 Incubator Lab Spares/Repairs

ITEM-44392

Precision Scientific NAPCO 5430 Dual Chamber Co2 Incubator Lab

This item was removed from a university where it was surplus to requirement.

It is in reasonably good cosmetic condition but does not power on, therefore it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Jouan SA CO2 Incubator Napco 6500 TC - No CO2 Connector Filter

ITEM-40981

Juan SA CO2 Incubator Napco 6500 TC Laboratory Incubator

This item was removed from a university laboratory where it was surplus to requirements.

The unit powers on and has been successfully temperature tested.

However, it is listed as spares or repairs because the CO2 connector filter is missing.

It is in good cosmetic condition.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Sanyo CO2 Incubator MCO-20AIC *Faulty CO2 Sensor* Lab

ITEM-42394

Sanyo CO2 Incubator MCO-20AIC Lab

This item was removed from a university laboratory where it was surplus to requirements.

The incubator powers on and is in good cosmetic condition.

It was functional when temperature tested, but it requires a CO2 sensor replacement due to displaying an E11 error code, which indicates a CO2 sensor abnormality.

Therefore, it is listed as Spares/Repair.

Included:

3 x Racks
Humidifier Tray

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Sanyo CO2 Incubator Model MCO-20AIC *Faulty CO2 Sensor* Lab

ITEM-42395

Sanyo CO2 Incubator MCO-20AIC Lab

This item was removed from a university laboratory where it was surplus to requirements.

The incubator powers on and is in good cosmetic condition.

It was functional when temperature tested, but it requires a CO2 sensor replacement.

Included:

3 x Racks
Humidifier Tray

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Sanyo MIR-154 Incubator Lab Spares/Repairs

ITEM-41674

Sanyo MIR-154 Incubator Lab

This item was removed from a university lab where it was surplus to requirement.

The item is in good cosmetic condition and powers on, but when tested, it displayed the message "E04 SSR or Comp relay is shorted," indicating that it cannot heat to its maximum temperature.

PHCbi recommends replacing the board as the only solution, so the item is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Nuaire IR Direct Heat Incubator Model-NU-5510E Lab Spares/Repairs

ITEM-37275

Nuaire IR Direct Heat Incubator Model-NU-5510E Lab

This item was removed from a university where it was surplus to requirements.

The unit powers up and has been successfully temperature tested.

However, due to a suspected CO2 Sensor/Air Pump fault, this item is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Kendro HERAcell 150 CO2 Incubator Lab Spares/Repairs

ITEM-39065

Kendro HERAcell 150 CO2 Incubator

This system was removed from a university lab where it was surplus to requirements.

The unit is in good working order and has been CO2 tested. It is in good cosmetic condition.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Kendro HERAcell 150 CO2 Incubator Lab Spares/Repairs

ITEM-44970

Kendro HERAcell 150 CO2 Incubator

This system was removed from a university lab where it was surplus to requirements.

The unit is not heating and requires a replacement relay. It is in good cosmetic condition.

Therefore, it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Napco Model 5410 Incubator Lab

ITEM-40040

Napco Model 5410 Incubator Lab

This item was removed from a university lab where it was surplus to requirements.

The unit powers up and is in good cosmetic condition. It was tested with a digital thermometer (not included).

It is in working order, but the safety set point is locked to 40˚C, therefore, it's listed as spares or repairs.

The CO2 function has not been tested.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Heraeus Biofuge Stratos Benchtop Centrifuge Lab Spares/Repairs

ITEM-44985

Heraeus Biofuge Stratos Benchtop Centrifuge

This system was removed from a university lab where it was surplus to requirements.

The unit is in fair cosmetic condition and powers on. However, it encountered the following issues during testing:

Set temperature reached -18°C but could not reach 37°C due to buttons becoming unresponsive.
Error codes, including E-24, were displayed, indicating "circuit is disconnected, overpressure switch of cooling plant tripped, expansion valve didn’t close."
Lid opening issues were experienced.

Additionally, a message from a previous client reported that the unit does not work.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

MSE Falcon 6/300 Refrigerated Centrifuge Lab

ITEM-38129

MSE Falcon 6/300 Refrigerated Centrifuge Lab

This item was removed from a university lab where it was surplus to requirement.

It is in good cosmetic condition and powers on; however, it failed the Portable Appliance Testing (PAT) for Earth Continuity.

Therefore, no further testing was conducted, and it is listed as for Spares/Repair.

Also included in this listing:

1 x Wingshielded Swing-Out Rotor 43124-756

Serial#: C12R0058

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Bio-Rad VersaDoc VDIS 3000 Imaging System Lab

ITEM-24680

Bio-Rad VersaDoc VDIS 3000 Imaging System

This was removed from a university lab where it was surplus to requirements.

The transilluminator did not power up.

It is sold for spares/repairs.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Thermo Scientific Model 232F-AEV-TS ES Series Freezer Lab Spares/Repairs

ITEM-41300

Thermo Scientific ES Series Freezer

Model:THERMO 232F-AEV-TS

This was removed from a university lab where it was surplus to requirements.

The unit powers up, but does not hold set temperature, therefore, it is listed as Spares/Repairs.

It is in reasonable cosmetic condition with marks from use.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Varian 3300 GC Gas Chromatograph Lab Spares/Repairs

ITEM-40071

This Varian 3300 GC Gas Chromatograph was removed from a university lab where ti was surplus to requirements.

The unit powers up but has no display and does not respond to inputs.

It is sold for spares/rpeairs.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Skalar Nitrogen Detector ND20 Lab Spares/Repairs

ITEM-41329

Skalar Nitrogen Detector ND20 Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition, but it does not power on. Therefore, it is listed as Spares/Repair.

Model-ND20

S/N-09114

Manufactured-2009

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Grant-Bio PHMT Series Thermoshaker For Microtubes and Microplates Lab Faulty

ITEM-29904

This Grant-Bio PHMT Series Thermoshaker was removed from a university lab where it was surplus to requirements.

This item is in good cosmetic condition with minor marks from use.

The unit powers up and heats, but does not shake. It is sold for spares/repairs.

Power supply not included.

SC-20 20 x 1.5ml

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Watson Marlow 205U Auto Drive 1PH With 205BA4 Four Channel Eight Roller

ITEM-42112

Watson Marlow Auto Drive 1PH 205U with 205BA4 Four Channel Eight Roller

This item was removed from a university lab where it was surplus to requirements.

The unit powers on and is in acceptable condition with some visible wear. It has passed a PAT test.

During testing, the unit operated correctly up to 30-40 RPM; however, an "Er. 2" error message displayed above this speed. A red warning symbol (!) appears next to the CCW setting, though it does not impact functionality up to 30-40 RPM.

Due to the fault listed, this item is listed as Spares/Repair.

Specifications:

Model: 205U Auto Drive 1 PH
Serial No.: 5120823
205BA4 Four Channel Eight Roller
Part No.: 023.0102.000
Issue: 1
Serial No.: 5110991

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Precisions Scientific Napco 5420-1 Incubator Lab

ITEM-37321

Precision Scientific Napco 5420-1 Incubator Lab

This item was removed from a university laboratory where it was surplus to requirements.

It powers up and is in good cosmetic condition, but due to a faulty fan, it does not maintain accurate temperatures.

As a result, this unit is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

RS Biotech Galaxy S 200 Incubator Lab Spares/Repairs

ITEM-45441

SLS Galaxy S 200 Incubator Lab

This item was removed from a university where it was surplus to requirement.

The unit powers up and the incubation is in good working order, but it has an issue with its CO2 sensor.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Captair 321 Smart Fume Hood Spares/Repair Lab

ITEM-46342

Captair 321 Smart Fume Hood

This item was removed from a university laboratory where it was surplus to requirements.

It is in poor cosmetic condition, with a failed visual PAT check due to an exposed fan and wires, which is caused by a missing lid or cover.

The unit does power on, and works. we used the cover from another ite

It is sold as Spares/Repair.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Jouan Napco CO2 1000 Incubator Spares/Repair Lab

ITEM-45442

Jouan Napco CO2 1000 Lab Incubator

This item was removed from a university laboratory where it was surplus to requirements.

It is in reasonably good cosmetic condition and powers on.

During testing, it successfully reached and stabilized at 37°C. However, it failed to climb any higher when set to 50°C.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Jouan MR23i BenchTop Centrifuge Faulty Motherboard Lab

ITEM-46344

Jouan MR23i BenchTop Centrifuge

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition, however, It is listed as spares or repairs due to a fault with the motherboard of the centrifuge. We are unable to conduct further testing.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Epson Stylus Pro 4900 Large Format Proofing Printer Model K181A Faulty

ITEM-42344

Epson Stylus Pro 4900 Large Format Printer Model K181A

This item was removed from a university laboratory where it was surplus to requirements.

It is in very good cosmetic condition and powers on but displays an error code - 159F, indicating an ATC Motor lock error.

Possible causes include a Roll Unit error, connection failure of the Roll Lock Sensor, or a connection issue between the SUB-D Board and the Main Board.

Therefore, further testing was prevented and it is listed as Spares/Repair.

Specifications:

Model: K181A
Serial#: MP2E018257
Year: 2013

Included:

1 x Epson Stylus Pro 4900 Software Disc Vol 1.2
1 x USB cable
1 x Setup Guide booklet

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Erbe EIP 2 Irrigation Pump With Vio-Cart Spares/Repair Lab

ITEM-44430

Erbe EIP 2 Irrigation Pump with Vio-Cart

This system was removed from a university lab where it was surplus to requirements.

The unit powers on but has not been tested further. It is in poor cosmetic condition, with the pump's plastic casing broken and held in place by a piece of tape.

A foot pedal is included.

Due to its cosmetic condition and inability to test further, this item is listed as Spares/Repair.

The system comprises the following:

ERBE EIP 2 Irrigation Pump

Vio-Cart

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Kendro HERAcell 150 CO2 Incubator Lab Spares/Repairs

ITEM-40990

Kendro HERAcell CO2 Incubator

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition.

This item does not power on, therefore it is sold as Spares or Repairs.

SPARES/REPAIR ITEM

£ 300.00 (ex. VAT) 1 in stock

Syngene GeneGenius Bio Imaging System With Digital Graphic Printer UP-D895MD

ITEM-45015

*Brand missing in title*

Syngene GeneGenius Bio Imaging System With Digital Graphic Printer UP-D895MD

This item was removed from a university lab where it was surplus to requirements.

It powers on and is in fair cosmetic condition with some wear.

The system includes:

Digital Graphic Printer UP-D895MD, which powers on and shows "Paper Empty." Serial No.: 74033
Syngene GelVue-GV2M20, which powers on, but the light is not very bright. Serial No.: SYGV2/1570
For this reason it is sold for spares/repairs.

No further testing was conducted.

System Serial No.: SYDR2-1566

SPARES/REPAIR ITEM

£ 295.00 (ex. VAT) 1 in stock

Buehler Metaserv Motopol 12 Grinder & Polisher Spares/Repairs

ITEM-35712

Buehler Metaserv Motopol 12 Grinder & Polisher

This was removed from a university lab where it was surplus to requirements.

The unit did not power up in testing. It is sold for spares/repairs.

It is in reasonably good cosmetic condition with marks from use.

Model1#: 95.C2640.250

Serial1#: 424 MH 244

Model2#: 95.C2269.250

Serial2#: 425-GPMV-247

SPARES/REPAIR ITEM

£ 295.00 (ex. VAT) 1 in stock

Lot Of Fortinet & Meru Duel Radio Access Points

ITEM-36010

Lot Of Fortinet & Meru Duel Radio Access Points

Included are;

75 x Meru AP822e V2

PN- 875-50068-C

10 x Fortinet AP822i V2

PN- 875-50069-F

(6 new in the box and 4 used)

9 x Fortinet FAP-U421EV-E

PN- P19552-03-04

Antennas are included with the access points

Brackets + Adaptors for each unit

This job lot of items comes from a university lab, The items were no longer required.

None of these items have been tested at our site - it is likely that some will be spares / repairs, but we anticipate that a reasonable amount should operate well.

None of these items have been PAT or electrical safety tested. For this reason we have marked these as spares/repairs as they should not be used without appropriate electrical safety checks.

They are sold as a spares/repairs bundle intended to be purchased by someone who has time to test and where necessary refurbish the unit. It is an excellent opportunity for anyone looking to benefit for individual equipment resale.

The units have not been tested at all.

SPARES/REPAIR ITEM

£ 295.00 (ex. VAT) 1 in stock

Walker Class 2 II Microbiological Safety Cabinet Class II 1290 Recirc Gen 6

ITEM-37037

Walker Class 2 II Microbiological Safety Cabinet Class II 1290 Recirc Gen 6

This was removed from a university lab where it was surplus to requirements.

The unit failed a visual PAT test and also does not power up. It has exposed wires.

The two exhaust HEPA filters have been removed and disposed of but the engineer was unable to remove the downflow filter as to do so would have involved completely dismantling the cabinet

It is in reasonable cosmetic condition with marks from use.

It is sold for spares/repairs.

SPARES/REPAIR ITEM

£ 290.00 (ex. VAT) 1 in stock

Genevac EZ-2 Personal Evaporator EZ2 STD Lab Spares/Repairs

ITEM-35470

Genevac EZ-2 Personal Evaporator EZ2 STD

This was removed from a university lab where it was surplus to requirements.

The unit powers up but the rotor does not work/turn.

It is in otherwise good cosmetic condition with minor marks

SPARES/REPAIR ITEM

£ 270.00 (ex. VAT) 1 in stock

Gilson HLPC System - Model 118, 306, 811C, 805, 506C Lab Spares/Repairs

ITEM-20198

This Gilson HLPC System was removed from a university lab where it was surplus to requirements.

The modules all power up, but the 118 UV/Vis detector has a faulty display and fan. Because of the age of the system, we have decided to sell it all for spares/repairs. It is likely there are faults with the other modules, but they may also be fine.

Included are the following;

1 x Gilson System interface module

Model 506C

1x Gilson Manometric module

Model 805

1x Gilson Dynamic Mixer:

Model 811C

3x Gilson Pumps:

Model 306

1x Gilson UV/VIS Detector:

Model 118

Serial cables:

2x 25 pin MALE to MALE cable

1x 25 pin MALE to FEMALE cable

1x Gilson Serial Input/Output Channel:

4 sets of( 2x FEMALE to 1x MALE 9pin connectors)

Manual:

1x Gilson 811C Dynamic Mixer User Guide:

The unit is in good cosmetic condition and appears to be complete.

Accessories:

1x 1x Gilson System interface module Power Supply:

1x Anachem Power supply w/ 9x IEC sockets:

1x Anachem Racking stand

Workshop

Filters