General Laboratory

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Safe Fast Classic 212D Class 2 Biological Safety Cabinet Spares/Repair

ITEM-51022

Safe Fast Classic 212D Class II Biological Safety Cabinet – Spares/Repair

This item was removed from a facility where it was surplus to requirements.

The unit is in good cosmetic condition and has passed initial internal checks. However, a fault has been identified during servicing.

The cabinet displays an “exhaust duct fault” error message. A new exhaust filter and exhaust fan have been fitted, but the error persists.

Additionally, the unit does not pass operator protection (KI Discus) testing, indicating it is not currently safe for operational use.

Due to this fault, the cabinet is being sold for spares or repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Eppendorf CryoCube F570h -86 Ultra Low Temperature Freezer Lab

ITEM-45131

Eppendorf CryoCube F570h -86 Ultra Low Temperature Freezer Lab

This item was removed from a facility where it was surplus to requirement.

It is in good cosmetic condition and powers on, however, during testing it failed to cool below -38ºc.

It is therefore listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Haier HR1200-II A2-D Class 2 Biological Safety Cabinet with Stand Lab

ITEM-50093

Haier HR1200-II A2 Class II Biological Safety Cabinet with Stand

This item was removed from a facility where it was surplus to requirements.

It is in very good cosmetic condition and powers on.

Last Service: June 2024

External dimensions (with stand): 138 (L) × 78 (W) × 216 (H) cm

Please note: Work table not included, it is therefore listed as Spares/Repair.

Key Specifications

Class II, Type A2 biological safety cabinet
HEPA/ULPA filtration (product and exhaust filtration for operator/sample protection)
EN 12469 compliant (model series standard)
Typical downflow velocity: ~0.45 m/s (model series spec)
Stand included (adjustable-height stand is standard for this cabinet/stand configuration)

Included Components

Haier HR1200-II A2 Cabinet
Stand

£ 500.00 (ex. VAT) 1 in stock

Brunel YDM Rotary Microtome Lab

ITEM-50347

Brunel YDM Rotary Microtome Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and in good mechanical order.

The previous owner described it as being in good working order.

£ 500.00 (ex. VAT) 1 in stock

Beckman Coulter SW 40 TI 40,000 RPM Swinging Bucket Rotor Lab

ITEM-48418

Beckman Coulter SW 40 TI 40,000 RPM Swinging Bucket Rotor Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and remains untested.

Specifications;

Platform: Floor Prep
Rotor Type: Swinging-Bucket (Ultracentrifugation)
Maximum RPM: 40,000 rpm
Max g-Force: 285,000.00
k-Factor: 137
Number of Tubes: 6×14 mL / 14×95 mm(6×14 mL / 1×4 in)

£ 500.00 (ex. VAT) 1 in stock

Job Lot of 13 Vintage Microtome Knives With Sharpening strops and Whetstones

ITEM-42018

Job Lot of 13 Vintage Microtome Knives With Sharpening Strops and Whetstones

These items were removed from a university lab, where they were surplus to requirement.

The knife blades are all in very good condition, with sharp and undamaged cutting edges, appearing to have been well maintained, except for the hand knife, which has a poor cutting edge.

The wooden boxes are in excellent condition, except for two that are damaged.

The lot comprises:

3 x Shandon Nothung C wedge shape 20cm blades (circa 1967) in box
1 x Shandon Northung A concave 25cm blade (circa 1967) in box
1 x Unidentified C wedge 18cm blade in box
3 x MSE Ltd No. 9057.W wedge 9cm blades in box
2 x Cambridge Instruments rocking microtome knives (10cm blades) in box
1 x Unidentified wedge 8cm blade in leather case
1 x Hand knife with handle in poor condition in box
4 x Leather sharpening strops (30-35cm long), 2 in box
2 x 15cm whetstones
1 x Acrylic 15cm sharpener
1 x 25cm blade holder
3 x 20cm blade holders
1 x 17cm blade holder

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Wheaton 753684-D 9 Deck R2P Roller Incubator Spares/Repair Lab

ITEM-46315

Wheaton 753684-D 9 Deck R2P Roller Incubator

This item was removed from a university laboratory where it was surplus to requirements.

It is in reasonably good cosmetic condition and powers on; however, during testing it took approximately 5 hours to reach 37°C, with a maximum recorded temperature of 57°C despite being set to 60°C.

Internally, it houses a Wheaton Modular Cell Production Roller Apparatus Model 3. The roller mechanism powers on, but the rollers moved very slowly during testing. The speed control dial is missing, and manually adjusting the underlying nut did not improve the speed.

Due to the above issues, this item is listed as Spares/Repair.

£ 500.00 (ex. VAT) 1 in stock

Union Carbide Liquified Gas Container Liquid Nitrogen Dewar Lab

ITEM-46190

Union Carbide Liquified Gas Container Dewar

This item was removed from a university lab where it was surplus to requirement.

It is in reasonably good cosmetic condition, we are unable to test it further at our facility.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Sanyo MDF-U442 Medical Freezer Lab Spares/Repairs

ITEM-44667

Sanyo MDF-U442 Medical Freezer Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, but it is not functional as it stays at ambient room temperature and triggers the alarm when the desired temperature is set.

Therefore, it is listed as Spares/Repair.

£ 500.00 (ex. VAT) 1 in stock

MSE 4 x 750ml Windshield Rotor 43124-708 BS4402 with Buckets Lab

ITEM-42469

MSE 4 x 750ml Windshield Rotor 43124-708 BS 4402 With Buckets

This item was removed from a university laboratory where it was surplus to requirements.

The rotor is in very good condition. It was tested on a compatible centrifuge at its maximum speed of 3660 RPM and operated without issues.

Includes:

4 x 750ml MSE buckets

Model: 43124-708 BS 4402

Serial No.: 872183

Max RPM: 3660

Year: 1987

£ 500.00 (ex. VAT) 1 in stock

Statebourne bio 36 Liquid Nitrogen Dewar with Trolley Lab

ITEM-50141

Statebourne bio 36 Liquid Nitrogen Dewar with Trolley Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and remains unteseted.

Features a trolley as displayed.

£ 500.00 (ex. VAT) 1 in stock

Infors AG CH-4103 Bottmingen HT TR-225 AK-82 Shaker Lab

ITEM-46239

Infors AG CH-4103 Bottmingen HT TR-225 AK-82 Shaker

This item was removed from a laboratory where it was surplus to requirements.

The shaker powers on and operates at the maximum RPM of 400.

It is in poor cosmetic condition.

Model: AK-82

£ 500.00 (ex. VAT) 1 in stock

Infors AG CH-4103 Bottmingen HT TR-225 AK-82 Shaker

ITEM-46240

Infors AG CH-4103 Bottmingen HT TR-225 AK-82 Shaker

This item was removed from a laboratory where it was surplus to requirements.

The shaker powers on and operates at the maximum RPM of 400. It is in reasonably good cosmetic condition.

Model: AK-82

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Spectrum Labs KrosFlo TFF System KR2i Peristaltic Pump Spares/Repair Lab

ITEM-48347

Spectrum Labs KrosFlo TFF System KR2i Peristaltic Pump – Spares/Repair

This item was removed from a university laboratory where it was surplus to requirements.

It is in good cosmetic condition and powers on; however, the previous owner has stated it is faulty, with the fault unspecified. Supplied with cables for connecting to the rest of a system, along with an Automatic Backpressure Valve (PN-900-13702-000).

Includes:

Cables for system connection
Automatic Backpressure Valve (PN-900-13702-000)

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Whatman/Parker Balston UHP Nitrogen Generator Model 76-94-220 - Spares/Repair

ITEM-46647

Whatman/Parker Balston UHP Nitrogen Generator Model 76-94-220

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, however, the previous owner has stated it is not in working order.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific Max Q 4000 Shaking Incubator Spares/Repair Lab

ITEM-50208

Thermo Scientific MaxQ 4000 Shaking Incubator – Spares/Repair

This was removed from a laboratory environment where it was surplus to requirements.

The unit powers on and is in good cosmetic condition with minor marks from use.

Following inspection and basic fault-finding, power is confirmed as reaching the unit and the PSU is functioning correctly.

However, power is not being passed through the control board to the PSU. This indicates a likely fault with the power control board.

The unit is therefore listed as Spares/Repair.

£ 500.00 (ex. VAT) 1 in stock

Triple Red Duo Organic 60 Ultra Pure Water Purification System Lab

ITEM-45397

Triple Red Duo Organic 60 Ultra Pure Water Purification System

This item was removed from a university where it was surplus to requirements.

It is in good cosmetic condition and powers on, we are unable to conduct further testing at our facility.

Included Components:

Avidity Carbon Pre-Filter
P/N: TR-2057
Install Date: 26/7/23
Avidity Cartridge Pack
P/N: TR-2050
Install Date: 26/7/23
Avidity Cartridge Polisher
P/N: TR-2051
Install Date: 26/7/23

Specifications:

Model: Organic 60 Ultra Pure Water Purification System
Serial No.: 0916961-01

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific HERAfreeze ULT Freezer HFU 2185 Basic-41 Lab Spares/Repairs

ITEM-42839

Thermo Scientific HERAfreeze HFU 2185 Basic-41 -80 Ultra Low Freezer Lab

This item was removed from a university lab where it was surplus to requirement.

The unit was described as "unreliable" prior to collection - it is sold for spares/repairs.

Specifications;

Model HFU 2185 Basic-41
Serial No. 020T-248264-0T
Capacity 572 litres

£ 500.00 (ex. VAT) 1 in stock

Genevac Technologies Table Lx130 Wx70 Hx82 cm Lab

ITEM-48653

Genevac Technologies Table (Lx130 x Wx70 x Hx82 cm)

This item was removed from a facility where it was surplus to requirements.

It was previously used with a Genevac VC3000TA and Genevac HT-8 system, with a vacuum pump mounted underneath.

The table remains in relatively good condition overall, with some areas of surface rust present.

£ 500.00 (ex. VAT) 1 in stock

Beckman Coulter SW 41 TI 41,000 RPM Swinging Bucket Rotor Lab

ITEM-48416

Beckman Coulter SW 41 TI 41,000 RPM Swinging Bucket Rotor Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and remains untested.

Specifications;

Rotor Type Ultra – Swinging Bucket
Maximum Speed 41,000 rpm
Maximum RCF at r max (g) 288,000 x g
k-Factor 124
Rotor Material Titanium
Bucket Material Titanium, Anodized Aluminum Cap

£ 500.00 (ex. VAT) 1 in stock

Scanbur Warming Cabinet Type-48-VS-III Lab

ITEM-44883

Scanbur Warming Cabinet Type-48-VS-III Lab

This item was removed from a university where it was surplus to requirement.

The unit powers up and is in good working order.

It is in good cosmetic condition, other than tape holding on a damaged alarm light cover.

£ 500.00 (ex. VAT) 1 in stock

Ohaus Frontier Micro Centrifuge FC5513 Lab

ITEM-49518

Ohaus Frontier Micro Centrifuge FC5513 Lab

This item is sold on behalf of a client where it is surplus to requirements.

This item is in complete working order, and in good cosmetic condition.

The normal terms and conditions do not apply to this item. This item is non returnable and non refundable.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

LTE Scientific Falcon 30 Benchtop Laboratory Autoclave - Spares/Repair Lab

ITEM-46403

LTE Scientific Falcon 30 Benchtop Laboratory Autoclave

This item was removed from a university lab where it was surplus to requirements.

The unit powers on and is in reasonably good cosmetic condition. However, it failed a recent service.

Therefore, it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

LTE Series 300 Autoclave Spares/Repair Lab

ITEM-46080

Autoclave Series 300

This item was removed from a university laboratory where it was surplus to requirements.

The plug has been removed by the previous owner, therefore, we could not test it any further.

It is in poor cosmetic condition. it si ultimately listed as spares/repairs for this reason.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Bellco Biotechnology Production Roller Apparatus Model 7340-10230 Spares/Repair

ITEM-49770

Bellco Biotechnology Production Roller Apparatus (Model 7340-10230) – Spares/Repair

This item was removed from a facility where it was surplus to requirements.

The unit is in poor cosmetic condition and is missing several rollers. The rear panels were loose but have been secured with new nuts and bolts. The item powers on, and the motor can be heard running; however, the rollers do not move at all.

Due to this operational fault and missing components, the unit is offered as Spares/Repair.

Model: 7340-10230

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Helmer iLF105-GX Freezer Spares/Repair Lab

ITEM-46454

Helmer iLF105-GX Freezer Spares/Repair

This item was removed from a university lab where it was surplus to requirement.

It is in good cosmetic condition and powers on, however during testing it was set to its minimum temperature of -20ºc and it failed to cool, instead rising in temperature from ambient.

Therefore, it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Systec DB-45 Autoclave Spares/Repair Lab

ITEM-46571

Systec DB-45 Autoclave Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition but does not power on, therefore it is listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Sorvall RC-3B Plus Floor Standing Centrifuge - Spares/Repair Lab

ITEM-46525

Sorvall RC-3B Plus Floor Standing Centrifuge - Spares/Repair Lab

This item was removed from a university where it was surplus to requirement.

It is in reasonably good cosmetic condition but has not been tested on site due to the service report attached stating;

Rotor lock: Seized, cannot remove rotor

No reported problems Service and check as above Unit is old

Note 6: door seal has shrunk and will not go back into place

Note 9: chamber is corroded due to substance.

Note 10: gas struts have failed, lid is heavy and can fall.

Note 12: drive shaft housing corroded.

Therefore, it is listed as Spares/Repair.

£ 500.00 (ex. VAT) 1 in stock

Millipore Direct-Q 3 UV Benchtop Water Purifier Lab

ITEM-48344

Millipore Direct-Q 3 UV Benchtop Water Purifier Lab

This item was removed from a facility where it was surplus to requirement.

It is in good cosmetic condition and powers on.

The lab confirmed it was in good working order prior to removal.

Please note; The Cartridges and Filters require replacement as the current ones have expired.

£ 500.00 (ex. VAT) 1 in stock

Eppendorf A-2-DWP 3,700 rpm Rotor

ITEM-46920

Eppendorf A-2-DWP Rotor

This item was removed from a university laboratory where it was surplus to requirements.

It is in good cosmetic condition. It was unable to be tested further.

Specifications:

Maximum speed: 3,700 rpm
Maximum RCF: 2,250 × g
Capacity: Accommodates up to two deepwell plates, microtiter plates, cell culture plates, or filtration plate kits
Compatible with Eppendorf Centrifuge models 5804, 5804 R, 5810, and 5810 R

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Beckman Optima TL Ultracentrifuge w/ Beckman TLA 100.4 Rotor Spares/Repair

ITEM-42968

Beckman Optima TL Ultracentrifuge

This item was removed from a university laboratory where it was surplus to requirements.

It powers on and is in good cosmetic condition with minimal wear. However, the unit is non-operational: it does not run programs or operate normally. The door does not open unless the unit is manually stripped down and the door lock pin is pressed.

Additionally, the vacuum chamber does not hold pressure. Error messages displayed include CPU, VAC, and SPD.

Therefore, it is listed as Spares/Repair.

Includes:

Rotor: Beckman TLA 100.4
Maximum Speed: 100,000 RPM
Serial No.: 95U1272

Model: TL

Serial No.: CTL95E13

£ 500.00 (ex. VAT) 1 in stock

Grant FH15 Flow Heater and FC20 Flow Cooler Lab

ITEM-42784

Grant FH15 Flow Heater and FC20 Flow Cooler

This system was removed from a university laboratory where it was surplus to requirements.

The FH15 Flow Heater powered on with the pump running. The heater light illuminated when the set temperature was increased above ambient.

The FC20 Flow Cooler powered on, and both the compressor and fan could be heard operating.

These units do not include a built-in tank and require an external header tank to function as part of a complete system. Due to this, full-range temperature testing was not performed.

It is in good cosmetic condition.

Includes:

Grant FH15 Flow Heater (Serial No. 72311)
Grant FC20 Flow Cooler (Serial No. 72311)

Model: FH15 / FC20
Serial No.: 72311

£ 500.00 (ex. VAT) 1 in stock

MVE XC 34/18 Nitrogen Dewar Aluminium 34 Litres Capacity

ITEM-42275

MVE XC 34/18 Nitrogen Dewar

This item was removed from a university where it was surplus to requirements.

The dewar is in good cosmetic condition, with signs of use.

Specifications:

Model: XC 34/18
Serial No.: ARB97K105
Capacity: 34 litres
Neck Opening: 9cm
Holds: 6 canisters

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Genevac VC3000TA Vapour Condenser Spares/Repair Lab

ITEM-48656

Genevac VC3000TA Vapour Condenser Spares/Repair Lab

This item was removed from a facility where it was surplus to requirement.

It is in good cosmetic condition, but was unable to be tested as it requires connection to a Genevac Centrifugal Evaporator. (Not included)

Additionally, the previous owner notified us that it was faulty, although the fault was not diagnosed,

It is therefore listed as Spares/Repair

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific Heraeus Megafuge 40R Laboratory Centrifuge Lab Spares/Repair

ITEM-47421

Thermo Scientific Megafuge 40R Centrifuge

This item was removed from a university laboratory where it was surplus to requirements.

The centrifuge displays an E33 error, indicating a fault with the main board. The working condition of the remaining parts is unknown:

2 x Lid locks (at least one reported to have an issue)
1 x Motor
1 x Compressor
1 x Display board
1 x Temperature sensor

Due to the issues stated above, this centrifuge is listed as Spares/Repair.

Please note: There is no rotor included.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific Forma Model Type - 906 ULT Laboratory Freezer 'Spares/Repair'

ITEM-42303

Thermo Scientific Forma Model Type - 906 ULT Laboratory Freezer Lab

This item was removed from a university lab where it was surplus to requirement.

It is in good cosmetic condition and powers on, however, when powered it displays a persistent "Wrong Power" warning with irregular compressor activity and fails to cool.

Therefore, it is listed as Spares/Repair.

Specifications.

Model: Forma 906
Serial#: 812688-2375
Year: 2009

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific Heraeus Megafuge 40R Laboratory Centrifuge Lab Spares/Repair

ITEM-47420

Thermo Scientific Megafuge 40R Centrifuge

This item was removed from a university laboratory where it was surplus to requirements.

The casing is in good used cosmetic condition. However, following internal components have been removed:

2 x lid locks/mechanisms
1 x motor

The main board is present but faulty and displays an E33 error on startup. The condition of other internal components—including the compressor, display, and temperature sensor is unknown and has not been tested.

Therefore, it is listed as Spares/Repair.

Please note: There is no rotor included.

RECERTIFIED ITEM

£ 500.00 (ex. VAT) 1 in stock

Sanyo MCO-175 CO2 Incubator Lab

ITEM-35162

Sanyo MCO-175 CO2 Incubator Lab

This item was removed from a university lab where it was surplus to requirement.

It is in good cosmetic condition and has been recertified. The CO2 and Heating features are working well.

This item is fixed with castors.

£ 500.00 (ex. VAT) 1 in stock

Sanyo C02 Incubator Model MC0-175 Lab

ITEM-37592

Sanyo C02 Incubator MC0175

This item was removed from a university where it was surplus to requirement.

The unit powers up and is in good working order (thermometer & co2 analyser not included).

It is in reasonably good cosmetic condition, however there is some rust visible and the control cover hinge has broken.

The door seal and latch are both in good cosmetic condition.

This item includes 4 x Shelves and a Humidity Pan.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Sorvall RC-28S Floor-Standing Centrifuge Spares/Repair Lab

ITEM-46923

Sorvall RC 28S Floor-Standing Centrifuge Spares/Repair Lab

This item was removed from a university lab where it was surplus to requirement.

It is in reasonably good cosmetic condition and powers on, however, testing could not be completed due to an on-screen error that prevented further operation, and prevented a vacuum from being drawn.

Therefore, it is listed as Spares/Repair.

£ 500.00 (ex. VAT) 1 in stock

LEEC Hot and Cold Laboratory Incubator Model PFC2CK Lab

ITEM-42425

LEEC Hot and Cold Laboratory Incubator Model PFC2CK Lab

This item was removed from a university lab where it surplus to requirement.

It is good cosmetic condition and good working order.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Hermle Z 300 K Centrifuge - Spares/Repair Lab

ITEM-47684

Hermle Z 300 K Centrifuge

This item was removed from a university laboratory where it was surplus to requirements.

It powers on and shows minimal wear.

However, during testing it failed to reach the set temperature, stabilizing at 25°C, and did not achieve the rotor’s maximum speed of 5000 RPM, reaching only 4000 RPM.

Therefore, it is listed as spares/repair.

Model: Z 300 K

Serial No.: 55060105

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Eppendorf 5804 R Centrifuge w/ A-4-62 Rotor Spares/Repair Lab

ITEM-49742

Eppendorf 5804 R Centrifuge w/ A-4-62 Rotor Spares/Repair Lab

This item was removed from a university where it was surplus to requirement.

It is in good cosmetic condition and powers on, however during testing the following error was present; Error 17, a PCB fault.

Which prevented any further testing.

It is therefore listed as Spares/Repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

PolyScience 6705 Refrigerated Circulator Spares/Repair

ITEM-46442

PolyScience 6705 Refrigerated Circulator

This item was removed from a facility where it was surplus to requirements.

It powers on and is in good cosmetic condition. However, it does not circulate antifreeze, and the unit failed to reach full cooling performance, only achieving a minimum temperature of 6.0°C.

Internal inspection revealed significant corrosion on the elements.

Due to these faults, this item is listed as spares or repair.

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Thermo Scientific Revco UXF Ultra Low Temperature Freezer Spares/Repair

ITEM-52383

Thermo Scientific Revco UXF Ultra Low Temperature Freezer Spares/Repair

This item was removed from a facility where it was surplus to requirement.

The unit powers on, however it powers down and restarts after approximately 3–5 minutes.

Additionally, on start-up, an error message is displayed: “Failed to connect to SD Card.”

No further testing has been carried out due to the fault described above. As such, the unit is offered as spares/repair.

Model: Revco UXF

Model No: UXF60086V

SPARES/REPAIR ITEM

£ 500.00 (ex. VAT) 1 in stock

Don Whitley MK3 Anaerobic Bench Top Work Station Spares/Repair

ITEM-42468

Don Whitely MK3 Anaerobic Bench Top Work Station

This item was removed from a university where it was surplus to requirement.

It is in reasonably good cosmetic condition but is not in working order, mainly due to a faulty gas inlet valve.

It powers on with functional temperature control and cooling fans. Key issues include non-working internal power sockets, flashing low CO2 and N2 warning lights, and a broken outer door lock seal knob, which compromises the chamber's sealing.

Due to the faults listed above, this system is listed as Spares/Repair.

Features:

Uses hydrogen, nitrogen, and carbon dioxide or a standard anaerobic gas mixture.
Digital temperature controller for constant temperature maintenance.
Humidistat-controlled condensing plate for excess moisture removal.
30-litre interchange lock capable of holding 108 plates with vacuum flushing.

Includes:

User Instruction Manual

Serial No.: 3170S

£ 500.00 (ex. VAT) 1 in stock

PALL ICELLIS Nano Perfusion Module Lab

ITEM-34860

PALL ICELLIS Nano Perfusion Module

This was removed from a university lab where it was surplus to requirements.

We do not have the correct PSU so it has not been tested.

It is in good cosmetic conditon with minor marks.

RECERTIFIED ITEM

£ 500.00 (ex. VAT) 1 in stock

Integra Cellspin Cell Control Magnetic Stirrer Four-Platform System Lab

ITEM-27676

Integra Cellspin Cell Control Stirrer Four-Platform System

This was removed from a lab where it was surplus to requirements.

The unit has been tested by a service engineer and is in full recertified working order.

This listing consists of:

1 x Integra Cellspin Controller.

4 x Integra Cellspin Platforms.

3 x 186050 2m Control Cables.

1 x 186238 Controller PSU.

This system will allow you to run either 1 or 2 x Platforms at once. Only one controller cable is needed for this setup.

The system includes 2 x spare platforms and 2 x spare control cables. Another controller could be purchased from the distributor to allow for 2 complete 2 platform systems. We can quote for an extra brand-new controller if required.

The platforms have all had brand-new belts fitted and have been rpm-tested through the range.

Note that these platforms require spinner flasks to operate correctly. These can be purchased separately from the distributor. We can also quote for these flasks if required.

£ 500.00 (ex. VAT) 1 in stock

Statebourne Cryogenics Biosystem BM 24 Automatic Liquid Nitrogen Refrigerator

ITEM-29642

Statebourne Cryogenics Biosystem 24 BM24 Automatic Liquid Nitrogen Refrigerator

This was removed from a university lab where it was surplus to requirements.

The system has had a brand-new power supply fitted and powered up. The water solenoid can be heard running.

It is in good cosmetic condition but has some marks on the front panel.

The keys are included.

£ 500.00 (ex. VAT) 1 in stock

DigiLab Pro Prep II Protein Digestion & Mass Spec Preparation Station 2 Lab

ITEM-29785

DigiLab Pro Prep II Protein Digestion & Mass Spec Preparation Station 2

This was removed from a university lab where it was surplus to requirements.

At our facility we were only able to power it up, but we are told it was in full working order prior to removal. The only issues is that the gas struts have failed.

It is in excellent cosmetic condition with hardly any marks from use.

There are various accessories included.