This Applikon Biotechnology EZ-Control Bioreactor System was removed from a university lab where it was surplus to requirements.

Included are;

Applikon Biotechnology EZ-Control Bioreactor System

Cat no. Z310110010

SN - P19208/2

Unit dimensions - L41 W37 H72cm

The unit powers on and boots up, but was not tested further.

Parts:-

Applikon Type P100e

Cat no. Z510000010

SN - P323750/19

Applikon Water Console

Applikon 7L Glas Biorector Vessel with Heat jacket

Trolley Dimensions - L108 W61 H144cm

Bottom Shelves - 70 x 59cm

Consumables/Accessories:-

Applikon 20L Appliflex Reusable pH & DO Sensors Cat no. Z650002040

Applikon 10L Appliflex Reusable pH & DO Sensors Cat no. Z650001040

Box of 2 x AppliSens Sensor Probes

Box of 1 x AppliSens Sensor Probe

Membrane Kit Z110000426

Ethernet cable

Various metal parts

Applikon Slotted Blindstopper M18 X 1.5

2 x Applikon Air Inlet Pipe+Porous Sparger 7L

Applikon Ribbed Blindstopper M30X1

Applikon Assembly Holder M10

Ass holder 6mm tube M18x1.5

Various probe cables

Applikon Licence file EZ Control + Manuals Dongle Z310110010

Heat Jacket - Powers on and heats up

This Beckman Coulter Cytomics FC 500 Cell Sorter System was removed from a university lab where it was surplus to requirements.

We had a qualified service technician test this system. It powers on as normal and communicates with the PC using CXP Cytometer software. The front lid mechanism is loose which makes it difficult to lift it up and the transparent screen isn't on correctly. They required more testing equipment to test it further.

Included are;

1 x Beckman Coulter Cytomics FC 500

Assy no. 6707249

1 x Beckman Coulter FC 500 (Unit on Wheels)

Assy no. 6807323

1 x Beckman Coulter Part no. A98490

1 x Spare Carousel

1 x DTX PC with CXP Software

2 x Eizo 19" Monitors

This Applikon My-Control Z310210011 Bioreactor Controller was removed from a university lab where it was surplus to requirements.

The unit powers up but we were unable to test it further at our facility.

It is in good cosmetic condition with marks from use.

This VisiTech VTI Laser & Controller System Yokogawa Scanner was removed from a university lab where it was surplus to requirements.

All the units power on but we were unable to test them further. They are in reasonably good condition with marks from use.

Included in the system is;

1 x VTI Laser Source Unit

1 x VTI AOTF Controller

1 x VTI AOTF Expansion Controller

1 X Set of keys for the laser unit

8 x Connection leads.

1 x Yokogawa CSU10B-F300-E./VisiTech QLC100 Spinning Disc Confocal Scanner

The unit is in reasonably good used cosmetic condition but it does have some scrapes/scratches and signs of use. It comes with a power supply, keys and some cables which may or may not be for the unit. The unit is also fitted with a filter wheel plate that is fitted with 4 filter lenses. It has been powered up but not we are not able to test it any further.

3 x Microscope filter assemblies.

Items are in good used cosmetic condition but they will probably require a clean.

The set consists of:

1 x 457/514/568/647 Filter Assembly.

1 x RGBA Filter Assembly with Semrock BrightLine.

1 x 405/488/568 Filter Assembly, doesn't appear to be complete.

Nikon SMZ1000 Microscope System with Modified Scanlaf Mars 1200 Class 2 Cabinet

This system was removed from a university lab where it was surplus to requirements. Everything is in good cosmetic condition with only minor marks from use.

Included are;

1 x Scanlaf Class 2 Biohazard Safety Cabinet Class 2

Model - Mars 1200

SN - L.10100812

Safe working area - 51 x 120cm

It powers up and is working. The up/down door function doesn't work, but we think this is likely due to the modifications. The heater for the microscope base has been tested and is working

1 x Nikon SMZ1000 Microscope

Parts:-

2 Eyepieces - C-W10xB/22

Plan Apo 1x WD 70

Model - C-FMC (1013443)

LV-TV

Camera W159P (00529)

TV Lens C-0.38x DN

The microscope is in working order.

RI IF Witness Stand holding:-

RI IVF Witness Heated Control Unit

SN - 00655

Powers on

Dell PC - Has RI Witness Program Installed

Other parts:-

Diagnostic Instruments Transmitted Light Base TLB D4.1 (Doesn't power on - It looks like it was fitted underneath the cabinet but removed due to not working)

HP USB-C Dock

RI IVF Witness Connection Box

Various cables

This Applikon My-Control Z310210011 Bioreactor Controller was removed from a university lab where it was surplus to requirements.

The unit powers up but we were unable to test it further at our facility.

It is in good cosmetic condition with marks from use.

SC Technical Services HP 500 HT-IR Heated IR UV Curing Conveyor Dryer Unit

This was removed from a university workshop where it was surplus to requirements.

The unit was confirmed as in working order with thermal (up to 130°C), IR and UV curing capabilities. It needs some maintenance and will likely need repair in the future.

The unit itself is 3m in length approximately 1.5m wide and 1.2m high and requires a three-phase electrical supply and ducted extraction to run.

Maintenance required – replace seals around oven lid and change UV bulb

Future repair – motors are in sealed (riveted) ducts and the bearings are worn and will need attention at some point.

There are no manuals included but the client has offered to demonstrate how to use it if required.

RareCyte CyteFinder & CyteSealer Liquid Biopsy Analysis System

This system was removed from a laboratory where it was surplus to requirements.

Both units power up and are in good cosmetic condition with marks from use.

It comes with 8 x Trays (53.5 x 16cm). One tray has been labelled as 'Not moving'

This Finnigan Trace GC Ultra & AS2000 Autosampler was removed from a university lab where it was surplus to requirements.

The unit is in good used cosmetic condition. It powers up fine and the oven heats.

The fan is very very noisy. We presume the bearings have gone in it.

It also comes with a Thermo Finnigan AS2000 Autosampler and C.U. Controller. The controller powers up.

Various cables are also included including a spare fan.

This Envair Pharmassist Positive Pressure Isolator Glovebox Workstation was removed from a university lab where it was surplus to requirements.

It powers on with air-flow and light working. it had been partially disassembled by the time it got to our site, but the lab confirmed that it was in full working order prior to removal.

The item is in a reasonable, used cosmetic condition with some marks from use.

Dimensions:-

Cabinet without Transfer Hatches - L180 W76 H140cm

Cabinet with Transfer Hatches - L300 W76 H180cm

Frame - L175 W70 H78.5cm

Internal Workspace - L179 W70 H92cm

Transfer Hatches removed/disconnected for transport/storage.

Internal dimensions - L60 W35 H29cm

2 x Hepa V Panels removed from the rear of the unit for transport/storage

Fuji Wrapper V FW3400 Horizontal Form-Fill-Seal Machine

This was removed from a laboratory where it was surplus to requirements.

The system has not been tested as a number of cables have been cut or disconnected. It will require a degree of decommissioning to get it back to working order.

Fuji Wrapper V FW3400 Horizonal Form-Fill-Seal Machine

Work order 03W233

SN - 103204

Product code - PHA3967

Source no. AC200V 50/60Hz

Asahi Kinzoku Model NR-80

SN - 402N9080076

This Hewlett Packard 6890 GC Gas Chromatograph System was removed from a university lab where it was surplus to requirements.

The system is in reasonably good cosmetic condition but it does have some marks and scratches from use.

All the components power up but have not been tested any further.

The system consists of:

1 x Hewlett Packard 6890 Series GC System.

It powers up and the oven runs.

1 x Hewlett Packard GC System Injector.

The unit powers up.

1 x Hewlett Packard 5973 Mass Selective Detector.

The unit powers up.

1 x Hewlett Packard GC Autosampler Controller.

The unit powers up and supplies power to the Injector.

1 x Hewlett Packard 59864B Ionization Gauge Controller.

The unit powers up.

This Siemens 3T Matrix Neck Coil 08622677 was removed from a university lab where it was surplus to requirements.

The unit has not been tested The lab believed it to be operational prior to it going into storage. It was being used with an operational Siemens 3T Magnetom Trio system up until a system upgrade.

It is in good cosmetic condition with only minor marks from use.

Interior Dims:

H23cm x W20cm x D15cm

This Ion Tech Ltd Etching Machine was removed from a university lab where it was surplus to requirements.

The lab manager reported they last used it around two years ago - the rotary pump worked at this point but they did not test the diffusion pump. They were able to ignite a plasma successfully which is reportedly key to the systems etching capabilities.

At our site, the system powers on but has not been tested further. It is in reasonably good cosmetic condition with some marks from use.